后端面

When end surface is neglected, the reflective energy will return to the filament efficiently if the filament is at the centre axis of the columniform lamp shell. 3 Compared with the straight tungsten filament that has a smooth surface, the helical one obtains higher absorbance which can achieve 0.6~0.7 under the actual screw pitch measurement.

当灯的管径为10 mm，而灯丝外径为1.5 mm时，节能可达12%到13%。2）对圆柱形灯外壳，在不考虑端面影响时，光源的灯丝若处于外壳的中心轴上，则反射的能量会有效地返回灯丝。3）螺旋结构的灯丝比表面光滑的直钨丝有更高的吸收率，灯丝绕成螺旋后在现行的螺距尺寸下吸收率能达到

Fault 4 drum fragile paper after the contrate boronizing, unable to pay-off Business card printing and membership card making

故障4卷筒易碎纸端面渗胶后，无法开卷制卡和会员卡制作

The friction coefficien of the bearings with ringlike flanges and spherical roller ends is decreased to 20%.

与普通轴承相比，改进后的轴承，轴向摩擦系数可以减小50%左右，其中环曲面挡边球端面滚子轴承可以减小80%。

And one end face is to an encapsulation after putting a cannery in among them, from this says it is also that one irrigates double the solid edge seal holding a hole with at the same time on significance.

而且其中一个端面是在装入罐头食品后封装的，从这种意义上说，它同时也是一个灌装孔的双重边牢固封口。

Press the axle end to the bottom, draw the brake wheel 2, and make it close to the tape of behind cover, revolve the nut 5 clockwise, make it touch with the brake wheel, continually revolve the nut for one to one and a half ring, lock the screw and wind window.

4顺轴下压转轴端部至底，提取制动轮2使其制动环与后端罩3锥面贴合，顺时针方向旋转锁紧螺母5，使其与制动轮端面接触，再将锁紧螺母继续按顺时方向转一圈至一圈半，上好锁紧螺钉和通风窗，调整完毕。

Hole , and use a stuff to seal the middle hole before the electrophoresis; after product electrophoresis, takes down the stuff and enters the drying oven to roast, when roasting in the hole causes the paint the residual liquid flow to cake in the two ends of the surface.

电泳厂在产品电泳前需进行前处理工序，清除产品表面的垃圾和锈迹，由于产品中孔不允许有油漆，在电泳前将中孔用塞头封闭，产品电泳后取下塞头进入烘箱烘烤，在烘烤时孔内残留的液体流到两端面造成油漆结块。

The electrophoresis factory must carry on before the product electrophoresis processes the working procedure, eliminates the product surface trash and the rusty stain, because in the product the hole does not allow to have the paint, before the electrophoresis hole with blind seal, after product electrophoresis, takes down enters the drying oven roasting blind, when roasting in the hole causes the paint the residual liquid flow to two end surfaces to agglomerate.

电泳厂在产品电泳前需进行前处理工序，清除产品表面的垃圾和锈迹，由于产品中孔不允许有油漆，在电泳前将中孔用塞头封闭，产品电泳后取下塞头进入烘箱烘烤，在烘烤时孔内残留的液体流到两端面造成油漆结块。

In this section we look at the theory behind the techniques used in rotary polishing and the effects that they have on paintwork and the results achieved.

在这里看抛光剂使用背后的理论，到底是怎么一回事，我们如何用好的抛光机和好的使用技巧来达到好的效果。

I'll dig like a psychotic rodent if I have to.

那我就帮你挖到中国去。