后柱

Methods Fresh litchi peel was air-dried, extracted with 70% ethanol solvent in ultrasonic wave. The extract was then purified with D101 macroporous resin adsorption chromatography, C18 solid phase extraction and high performance liquid chromatography. And the component purified was identified by mass spectrography.

新鲜荔枝果皮阴干，用70％乙醇溶液以超声波浸提法提取，提取液经过D101大孔树脂吸附层析、C18小柱固相萃取、高效液相色谱法分离、纯化后，采用质谱法鉴定结构。

After the bag had been filled by gravity, the tourniquet was released and a spring clip was placed across the tube distal to the exchange column.

当这个袋子被重力填充后，止血带被释放，弹簧夹横跨管通过远端管被安置在交换柱上。

Taken example for solving real engineering problem, the methods and steps for the analysis of the steering-wheel vibration is discussed.

为了解决某型轿车的转向盘振动问题，本文通过对影响转向盘振动的诸多因素逐一进行分析，结合先进的试验手段和CAE分析技术，找出了引发该轿车转向盘振动的主要原因是车轮动平衡质量不合格及固定转向柱管的仪表板横梁刚度不足，通过提高车轮动平衡质量，改进仪表板横梁设计，提高仪表板横梁的刚度和固有振动频率，结合道路试验进行主观评价，改进后的转向盘振动达到了平顺性要求。

Methods: The sample was absorbed with glass fiber filters paper and was desorpted by toluol. Trinitrotoluene was analyzed by capillary gas chromatography method with ECD detector.

用玻璃纤维滤纸采集空气中的三硝基甲苯，用溶剂洗脱后，经色谱柱分离，电子捕获检测器检测。

Rollerblade, Inc. developed ABT or 'Active Brake Technology'.A fiberglass post attached at one end to the top of the boot and at the other end to a rubber-brake, hinged the chassis at the back wheel.

1993-Rollerblade公司发展了ABT（Active Brake Technology，主动刹车技术），一个玻璃纤维柱粘在靴子的后顶部，在鞋子另一端则粘在橡胶刹车皮上，并接在后轮的底盘上。

The Trefoil knot, a main exhibit in the middle of the hall, is 10 meters wide, 12 meters high, with bandwidth of 1.65 meters. It is made from triangular prism band.

三叶纽结整体宽度10米，高12米，带宽1.65米，是由一条三棱柱带经过三次盘绕，将其中一端旋转120度后首尾相接，由此构成三面连通的单侧单边三叶纽结造型。

Using the triangular prism element can finished the simulation of IP\'s parameters under the undulate topography.

使用三棱柱剖分单元对大地模型进行剖分，在给出地表节点上的高程值后，可实现起伏地形条件下的激电参数的正演模拟。

We used ITO glass substrate and high purity（99.99%） titanium , put to use sputtering process, add to high purity O2 make it complete the best structure film and the thickness about 1400 . By way of 500℃ anneal could got a better anatase phase, this result could easy reaction with electrolyte to increase electron-transferred. Used as spin casting covering PR on ITO substrate, transferring patterns of array circular shapes on a mask to photography, used optimize temperature and time to hard bake. Finally used HCl to etching underexposed TiO2 area, and acetone to tripper top PR, make it to accomplish pillars shape TiO2 electrode.

本研究使用ITO玻璃基板为底材在以高纯度钛(99.99%)为靶材，利用溅镀方式通入纯氧使其行成高纯度TiO2镀於ITO基板上行成厚度约1400的薄膜，且经500℃高温烧结使其行成最强的锐钛矿结晶相，此晶相有利於与电解液反应进而增加电子的转移，提升太阳能电池最佳的效率，在以旋转涂布方式铺上光阻，以矩阵排列的圆孔光罩曝光、最佳的温度及时间来烘烤、显影后；使用盐酸以等向性湿蚀刻方式蚀刻未曝光之TiO2区域，最后利用鈵铜将最上层光阻去除，使其行成柱状TiO2的电极。

Adenosine was used as the raw material, dissolved in triethyl phosphate and then esterified with thiophosphoryl chloride under 0~5℃ for 8h without water and oxgen, in alkaline condition provided by 2,6-dimethylpyridine, introducing thiophosphoryl ester to adenosine.Then superfluous triethylamine was added and reacted under 5℃ for 1h to synthesize rough 5'-AMPS.The unpurified product was appled to a DEAE Sephadex A-25 column and eluted with triethylammonium bicarbonate.

用腺苷为起始原料，溶解于磷酸三乙脂中后，在无水无氧环境中及2，6-二甲基吡啶提供的碱性条件下与三氯硫磷以0~5℃下发生酯化反应8h，将硫代磷酸酯引入腺苷，然后再与过量三乙胺在5℃下反应1h，合成粗产品，再用碳酸氢三乙胺作洗脱液，过DEAE Sephadex A-25凝胶柱纯化。

Chromium and iron oxide supported silica-pillared zirconium phosphates with high surface area have been prepared successfully by the new method as well.

2同样采用先负载后再焙烧的方法，制备了大比表面负载氧化铬和氧化铁的氧化硅层柱磷酸锆，进一步表明此方法具有一定的普遍意义。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。