后孔

Spring plate after hanging parts of the main plane of the surface and pore.

后钢板弹簧吊整机的主要加工表面是平面及孔。

After drilling the holes, use self-tapping screws to secure the drawer face frame with the door panels.

孔打好后，直接用自攻钉把抽屉前板和门板固定，门板底部平齐柜底板。

The actual deformation observation instrument not only results in confused and false readings ,but also high cost , difficult hole sealing .

现行的变形观测装置不仅造成观测成果的混乱与假象，而且成本高、封孔困难，改进后的岩石抬动变形观测装置克服了现行变形观测装置的不足之处，提高了可操作性。

In addition there will be a part of compressor running metal end of the refrigerant itself contains a certain amount of impurities, as the refrigerant in the refrigeration system, circulation changes, which will plug into the expansion valve valve Bellows Seal Valves hole, into the compressor will nap, and scratching the cylinder.

另外压缩机运行后也会有一部分金属末，制冷剂本身也含有一定数量的杂质，随着制冷剂在制冷系统内循环变化，它们进入膨胀阀就会堵塞阀孔，进入压缩机就会拉毛和刮伤汽缸。

The results show that the aluminum coatings with seal coat are better sealed and can prevent the oxidation atmosphere pervasion into the inner coating .

结果表明，电弧喷涂铝涂层经封孔后，涂层的密封程度大大提高了，可以更好地阻挡或减缓氧化气氛向涂层内部的渗透，提高了涂层对基体的保护效果。

4 Of the nominal size DN ≥ 200 of the valve, the valve cover can be processed in a screw, after trial, must be plugged with metal plug screw.

4.3.4对公称尺寸DN≥200的闸阀，可在阀盖上加工出一个螺孔，试验完毕后，必须用金属螺塞堵塞。

When the oil level in the lower casing reaches the intermediate mark in the oil window (not stop feeding oil to the gear reducer from filter press), startup oil pump in the lubricating station to feed oil to lower casing. In order to assess the oil level in the upper casing, it is allowed to remove the plug screw of observation hole at thrust bearing oil sump in the upper casing.

较为方便的方法是拆除减速机箱体中分面法兰上的呼吸器，利用其安装孔对减速机下箱体进行加油，当减速机下箱中的油位到达后油窗中间刻线时（不停止滤油机对减速机的加油），可以启动润滑站油泵对减速机上箱体进行加油。

Cut file, sawing skills by learning the grip, standing position, body movements, and many other points force factors and the impact of the traditional grip of the emergence of file-grip handle to stand up after slightly outside the site of the palm, when a file cut Force, after the file handle a gradual shift,"hold" to "grasp", resulting in the introduction file enough; saw grip handle full point higher than the thrust of the saw blade to install center hole of about 30mm, the high point of thrust is likely to result in the bow saw On both sides of the swing, resulting in a broken saw blade and saw seam askew.

锉削、锯削技能的学习是受握法、站立部位、身体动作、作用力点等诸多因素的制约和影响的，传统的握法出现握锉柄后顶住部位稍偏离手心，锉削时一用力，锉柄逐渐后移，&握&变成&抓&，造成锉刀推出力度不足；满握锯柄的推力点高于锯条安装孔中心约30mm，偏高的推力点很容易造成锯弓向两侧摆动，造成锯条折断及锯缝歪斜。

If you want to make it, you first take out some of flours, then mix some water to paste. After rolling average, you put them in the pot. When the water is boiled in the big iron caldron, you put a little block of paste on the iron board and rub hard and paste change to very short noodles , we call them "Gegedou". When you eat them, you will feel them very smoothly. If you mix some good soup, it is very delicous.

如果想吃的时候，就把面取出一部分，然后用水活好放在盆里，当锅里的水开了后，把一小块面放在有孔的铁板上用手用力向下搓，面团就变成很短的面条了，我们叫它&格格豆&，吃到口里的感觉别光滑，再做一些好吃的汤混在一起吃，味道好极了。

The present invention relates to a kind of tunable plasma resonant cavity for PCVD optical fiber perform rod processing machine. The tunable plasma resonant cavity includes cylindrical resonant cavity casing and cut-off waveguides set on two ends of the casing, and features the tuning piston, which is set on one end of the cylindrical resonant cavity and has middle part with through hole and back end stretched beyond the casing.

本发明涉及一种用于PCVD光纤预制棒加工机床的可调谐等离子体谐振腔，包括有圆柱型谐振腔壳体，在圆柱型谐振腔壳体的两端设置截止波导，其不同之处在于在圆柱型谐振腔腔体的一端安设调谐活塞，调谐活塞的中部开设通孔，后端延伸至圆柱型谐振腔壳体外端。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。