合金的

Main Applications: Molybdenum Power is mainly used for machining wire, Molybdenum liner board, electronic components, pure molybdenum or molybdenum alloy sintered products etc., precision alloy can also be used as additives.

用途：钼粉用于加工钼线材、钼板衬、电子元件、纯钼或钼合金烧结制品等的原料，还可用作精密合金的添加剂。

It is found that the microstructure of alloy is consisted of two phases, a main phase of V based solid solution phase, and the second phase of Laves phase. The alloy has remarkable hydrogen storage properties at room temperature and 353 K, the maximum hydrogen desorbing capacities are 3.11 wt% and 2.31 wt%, respectively.

研究发现：该合金为两相结构，主相为V基固溶体，第二相为Laves相；在室温和353 K时合金的放氢PCT曲线上有明显的压力平台，最大放氢量分别为3.11%和2.31%。

Based on the principles of chemical corrosion, this article discussed how to use variant erodents of nitric acid in alcohol to reveal the metallographic structure of one phase alloy and multiphase alloy .

作者从化学腐蚀原理出发，对不同浓度的硝酸酒精侵蚀剂显示单相合金与多相合金的金相显微组织进行了研究和探讨。

The effect of mischmetal is greater than that of B, Ti.Salt-refiner decreases the strength of quasi-solid and the failure strain of the alloy.

合金的中添加盐类细化剂后，合金准固态强度和断裂应变都比未加盐类细化剂的要低

The understanding of deformation characteristics is the prerequisite for quality control of P/M superalloy components.

了解粉末高温合金的成形规律是控制粉末高温合金制件质量的重要前提。

Therefore, the proposed model can lay foundation of the quality control and process design for the forging process of GH761 superalloy

根据实验结果，建立了GH761合金动态再结晶过程的物理模型，为科学设计和有效控制GH761合金的锻造工艺提供理论依据

Mechanical properties of superalloy Inconel751 after standard heat treatment followed by long time aging treatment at 700℃and 850℃ respectively were tested at room temperature and high temperature.

对经过标准热处理Inconel751合金，在700℃和850℃进行长时间的时效处理，测试常温和高温下合金的力学性能，对组织和断口进行观察。

Mechanical properties of superalloy lncone1751 after standard heat treatment followed by long time aging treatment at 700℃ and 850℃ respectively were tested at room temperature and high temperature.

对经过标准热处理Inconel751合金，在700℃和850℃进行长时间的时效处理，测试常温和高温下合金的力学性能，对组织和断口进行观察。

To improve the fatigue strength of TC4, Nd: Glass pulse laser was used to shock the surface of TC4. X-ray stress analyzer was used to test the residual stress of the shocked area, and calculation was done by finite element software ABAQUS.

为提高钛合金的疲劳强度，采用Nd： Glass强脉冲激光对TC4钛合金表面进行冲击强化处理，采用X射线应力仪对冲击区的残余应力场进行测试，并采用ABAQUS有限元仿真软件对其残余应力场进行分析计算。

The damping capacity was measured using reversal torsion pendulum.

采用倒扭摆测试合金的阻尼性能，XRD测试合金的层错几率和ε马氏体体积分数。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。