合金法

The mainly preparation of ferrovanadium is aluminothermic reduction currently.

钒铁是生产工具钢、耐热钢的一种重要中间合金，目前主要采用铝热法生产。

The out- of- pile and in- pile corrosion,mechanical properties,microstructure,hydrogen absorption,creep and growth resistances of M5 alloy using as PWR fuel rod cladding materials developed by FRAMATOME in France has been summarized with reference to the literatures.

概述了法国法马通公司开发的新型燃料包壳材料 M5合金在堆内外的腐蚀、吸氢、显微组织、蠕变、辐照生长等性能。

The fatigue is analyzed for the SENT specimen of TA6V titanium alloy at different stress ratio and on different stress level by the general finite element analysis software ANSYS. The dangerous fatigue location is predicted by the nodal stress Y-direction of the hemicycle notch for TA6V titanium alloy SENT specimen. Based on the local stress-strain method and the material S-N graph, the nominal stress-strain of the specimen is converted to the local stress-strain of the dangerous location by the elastic and plastic finite element analysis, thus the fatigue life is estimated by Miner fatigue damage accumulation theory and compared with the fatigue test of small crack growth.

借助大型通用有限元分析软件ANSYS对TA6V钛合金SENT试样在不同应力比和不同应力水平下进行疲劳分析，根据SENT试样缺口处的应力状态分布预测疲劳危险部位，采用局部应力应变法，结合材料循环的S-N曲线，通过弹塑性有限元法将构件上的名义应力谱转换成危险部位的局部应力应变谱，从而根据危险部位的局部应力应变历程采用Miner累积损伤理论对构件的疲劳寿命进行估算，并与疲劳小裂纹试验数据进行比较分析。

In this article, a mathematical model of enthalpy of formation for rare-earth hydride is established on the basis of the experimen...

本文应用微观结构参数法和大量的实验数据，建立了稀土贮氢合金氢化反应生成热的数学模型。

In addition, by using bondtype and polyhedron cluster type index methods to analyze the transformation of the microstructure, not only the key role of icosahedron in amorphous formation and stability can be explained, but also the solidification processes and the configuration characteristic of amorphous metals understood deeply.

此外采用键对及原子多面体类型指数法对凝固过程中微观结构组态变化的分析，不但能说明二十面体结构在非晶态合金形成和稳定性中所起的关键作用，又有助于对液态金属的凝固过程、非晶态结构特征的深入理解。

The high temperature impact fatigue characteristics of aluminum matrix composites reinforced by aluminum silicate fibre in comparison with ZL109 by squeeze casting has been studied.

采用加压铸造法来制备硅酸铝短纤维增强铝合金复合材料，并通过与ZL109合金的对比试验，研究高温下材料的冲击疲劳特性。

The joining of magnesium and aluminum was made successfully by fusion- brazing welding method with interlay plating.

镀层法，即采用熔—钎焊的方法成功实现了镁合金和铝合金的连接。

The research and development on formation of Ni_3Al intermetallic compounds by mechanical alloying are presented.

本文综述了用机械合金化法制备金属间化合物Ni3Al的研究现状和发展情况。

The experiment results of Al-Mg-Sc-Zr alloy plate show that the precision of H-M inverse pole figure calculated by LG method has the obvious superiority over other current approximated methods.

Al-Mg-Sc-Zr合金板材反极图测算实验结果表明，由LG法所测算的H-M反极图精度显著地高于各种现行的近似方法。

A new method was studied for the determination of lanthanum in molybdenum alloy s by ICP-AES.

建立了电感耦合等离子体原子发射光谱法测定钼合金中镧的分析方法。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。