可焊的

The solderability of benzimidazole films on the surface of copper is investigated by solder float test. Several factors which influence solderability of the films are discussed.

采用上锡率法研究了咪唑化合物在铜表面所成保护膜的可焊性，并探讨了咪唑化合物类型、膜厚、再流焊次数及高温热冲击对该膜可焊性的影响。

Our process capability: Plates: FR4, High TG FR4, high CTI FR4, high frequency materials, halogen-free materials, aluminum and other low-rise Materials :2-20 layer of finished copper thickness :0.5-5 OZ finished thickness: 0.2 -6.0mm Minimum line width: 3mil Minimum line spacing: 3mil smallest shape tolerances:+/-0.1mm minimum finished diameter: 0.1mm maximum thickness aperture ratio: 12:1 wide minimum solder bridge: 4mil characters minimum line width: 5mil Minimum height of characters: 30mil Solder Mask Color: Green, black, blue, white, yellow, purple characters such as color: white, yellow, black and other surface processes: spray tin, lead-free HASL, Electroless gold plating Shuijin, OSP, chemical Shen tin, silver and other chemicals Shen Process: Goldfinger, blue gum, Blind-via/Buried-via, characteristic impedance control, rigid-flexible combination of reliability testing such as: Open / Short testing, impedance testing, solderability testing, thermal shock testing, metallographic analysis of micro-slice curvature Isoptera: 0.7% flame retardant Level: 94V-0

我们公司的制程能力：板材：FR4、高TG FR4、高CTI FR4、高频材料、无卤素材料、铝基材料等层数：2-20层成品铜厚：0.5-5 OZ成品板厚：0.2-6.0mm最小线宽：3mil最小线间距：3mil最小外形公差：+/-0.1mm最小成品孔径：0.1mm最大板厚孔径比：12：1最小阻焊桥宽：4mil最小字符线宽：5mil最小字符高度：30mil阻焊颜色：绿色、黑色、蓝色、白色、黄色、紫色等字符颜色：白色、黄色、黑色等表面工艺：喷锡，无铅喷锡、化学沉金、电镀水金、OSP、化学沉锡、化学沉银等其它工艺：金手指、蓝胶、盲埋孔、特性阻抗控制、刚柔结合等可靠性测试：开/短路测试、阻抗测试、可焊性测试、热冲击测试、金相微切片分析等翅曲度：≤0.7%阻燃等级：94V-0

The welding of end ring of alternating current machine and the conducting bar is the key technology for manufacturing of asynchronous traction motor with high power. China South Locomotive and Rolling Stock Industry Corporation had taken this significative study as a key project for the manufacturing of alternating current machine. According to the welding of end ring of alternating current machine, the welding of copper and copper alloy is described in this paper. Results obtained in this study are as follows. 1.By the comparison of oxyacetylene gas brazing, induction brazing and resistance brazing, it was found that high-quality welding joint could be obtained by induction brazing, which also had the highest efficiency.

交流电机端环与导条的焊接是大功率异步牵引电动机制造的一项关键技术，开展其焊接工艺研究具有重要的意义，中国南车电机公司将此课题作为解决交流电机制造的一个重点项目，本文结合交流电机转子端环焊接的课题，对铜及其合金的焊接进行了研究，主要研究结论如下： 1、通过氧乙炔火焰钎焊、感应钎焊、电阻钎焊等焊接方法的对比试验发现感应钎焊可获得优质的焊接接头，且感应钎焊的焊接效率也是最高的。

"It is understood that all steels are weldable, flat and free from unweldable coatings."

当然，所有的钢应是可焊的、平的、没有不能焊的涂层。

Some materials are weldable,while others are not.

一些材料是可焊的，而另一些则是不可焊的。

Not all aluminum alloys are weldable.

不是所有合金都是可焊的。

A few of the 7XXX series defy the general rule and are weldable.

一些7XXX 系列合金不符合常用规律，它们是可焊的。

Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels.

无正火或正火态的可焊的细晶粒钢的交付技术条件

Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels.

已经过热机械处理的可焊的细晶粒钢的交付技术条件

The tack welding and interior/outerior welding can improve welding speed and quality, and control welding quality effectively

采用先预焊后内外焊的工艺，可在最佳位置实现焊接，焊接速度快、效率高，不易出现错边、焊偏和未焊透等缺陷，有效控制焊接质量

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐