可注射的

Can be replaced without needle injection head: no needle injection by the injection of the top head, piston, and a circular ring formed ...

可更换的无针注射头：无针注射头由注射顶端、活塞和一个圆形密封圈组成。。。。

It is designed for the production of water in oil injectable emulsions.

它被设计成适合油包水的可注射的乳液剂产品。

Because of wide applications of injectable CPC, improvement of its injectability becomes the hot issue of the research.

由于可注射CPC的广阔应用前景，改善CPC的可注射性已成为CPC的研究重点。

Salk developed the first, injectable polio vaccine; Sabin developed an oral vaccine that would eventually supplant it.

Salk研制出第一次的可注射的小儿麻痹症疫苗；而Sabin研制出一个口服疫苗，它可以最终取代它。？

Injectable agents are the most rapid and reliable and are preferred when venipuncture can be accomplished without causing fear to the animal or unnecessary risk to the operator.

可注射的药剂肯定是最为迅速以及可靠的首选。静脉注射可以在不导致动物害怕或者是导致操作者风险的情况下顺利完成。

Methods BMSCs isolated from rabbit iliac bone marrow were culture-expanded in vitro. The injectable tissue-engineered bone constructed from autologous PRP, FG, and BMSCs was cultured in vitro, and its biological characteristics were observed including the time of gel formation, histological features, seed cell survival and microscopic structures. Results The constructed injectable tissue-engineered bone began gel formation within 20 to 30 s, and after a week-long culture, the gelatine began to degrade, and numerous well viable fusiform cells could be seen to adhere to the bottom of the Petil dish, Scanning electron microscopy identified globular and olivary cells embedded in the fibrin glue, and numerous small particles could be seen around of the cells.

从兔髂骨处抽取骨髓体外培养BMSCs并诱导向成骨细胞分化，抽取兔自体动脉血提取PRP，以FG、BMSCs、PRP共同构建可注射型组织下程骨并体外培养观察其生物学特性如凝胶形成时间，组织学特点、细胞存活情况及其超微结构特征等结果构建的可注射型组织工程骨可在短时间内形成凝胶，体外培养1周时其中细胞生长良好，电镜下见纤维蛋白网格结构致密，种子细胞及血小板颗粒分布广泛。

Purpose The clinical prospects of injectable calcium sulfate were verified through the mechanical tests, degradation and osteogenesis abilities' experiments, and the physicochemistry characteristics and biomechanical appreciation were evaluated.

对可注射式硫酸钙理化性能和生物相容性进行检测，通过动物实验研究其力学稳定性、降解性能及成骨性能，探讨可注射式硫酸钙的临床应用能力。

Sixty-two artificially respired rabbits were anesthetized with urethae.Intranuclear microinjection was adopted.Microinjection of TRH into Lc-Sc induced a marked increase in respiratory frequency and significant elevation of blood pressure.The above mentioned effects of TRH into Lc-Sc on RF could be blocked by preinjection of α2 or β receptor antagonist into RVLM respectively.

实验选用62只行乌拉坦静脉麻醉和人工呼吸的家兔，采用脑内核团微量注射的方法，将TRH微量注入蓝斑复合核，使呼吸频率明显增快，平均动脉血压升高；在延髓头端腹外侧区分别预注射α2或β受体阻断剂，使TRH在蓝斑复合核的呼吸增频效应明显减弱，其升压效应可被延髓头端腹外侧区分别预注射α或β受体阻断剂拮抗。

Plastic Injection the design process, which is designed as part of the craft-oriented establishment : Plastic Parts of the Process Analysis, Plastic Parts of the size and quality of calculation and the injection parameters set; Structural design : Surface choice cavity determination, Cavity the arrangement, gate design, lateral type pulling mechanism design, launch and reattached body identified; Core, Cavity size calculation; Die heating and cooling system computation; Mold closing high set; Injection machine parameters in the verification; The design of such a structure can be used to ensure reliable die.

注塑模中文摘要翻译成英文摘要？？？帮帮忙~~~救急啊塑料注射的设计过程，其中的设计内容有零件的工艺性编制：塑件的工艺性分析、塑件的体积和质量计算及注射机参数的确定；结构设计：分型面选择、型腔数确定、型腔的排列方式、浇口设计、侧向分型抽芯机构设计、推出及复位机构方式确定；型芯、型腔尺寸计算；模具加热和冷却系统计算；模具闭合高度确定；注射机有关参数的校核；如此设计出的结构可确保模具工作运用可靠。

Objective To investigate the biomechanical behavior of injectable recombinant human bone morphogenetic protein-2 (rhBMP-2)/calcium phosphate cement used in vertebroplasty in primate models. Methods Two fresh cadavers of adult rhesus were used as group Ⅰ, and 4 adult rhesuses were divided into groups Ⅱ and Ⅲ.

复合重组人骨形态发生蛋白-2的可注射磷酸钙骨水泥在椎体成形术中的目的探讨自主研发的复合重组人骨形态发生蛋白－2(rhBMP-2)的可注射磷酸钙骨水泥应用于猕猴椎体成形术早期和后期生物力学性能。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐