可模压的

The analysis result could be theoretical reference for parameters amelioration and further optimization design of tool.

其分析结果可为模压工艺的改进，特别是模具的进一步优化设计提供理论依据。

The green grassy organizer is made of soft molded rubber and can hold a variety of items.

绿色草地的组织者是由软模压橡胶，可容纳各种不同的物品。

Preparation of the cathode includes:shaping under the press of 40Mpa, sintering at 550℃for 1 hour and at 900℃for 8 hours and threading with molybdenum bar; Considering the literatures we choose CaCl2 as salt for preparation titanium. Pretreatment of salt is for 1 hour at 100℃and for 2 hours at 300℃. Partial pressure of oxygen which need lower than 5.11×10-7Pa to reduct titanium oxides and hygroscopic property of salt need a sealed equipment to electrolyse. And finally successfully designed a satisfied one and the results show that the equipment can be satisfied the requirment of the experiment. Flow of the inert gas is 1.5L/min, the voltage is 2.8 V, temperature is 850℃and time is 2 hours during pre-electrolysis. Flow of the inert gas is 0.2L/min, the voltage is 3.1 V, temperature is 900℃and time changes with the mass of TiO2 during electrolysis, namely the greater need the longer time; To eliminate influence of salt and other impurities, the products need to wash with distilled water and dilute chlorhydric acid , then wash with dilute hydrochloric acid under supersonic wave assistant. Finally, electrometical properties of the electrolysis of TiO2 is researched by cyclic voltammetry and chronoamperometry, and results show that there are two main reodox steps, namely from TiO2 to TiO and from TiO to Ti.

阴极制备主要包括40MPa压力下模压成型、两段式烧结(1小时内升至550℃保温1小时，再1小时升温至900℃保温8小时)及烧结后TiO2块打孔用钼棒串接三个主要环节；实验中选用CaCl2作为电解熔盐，并对其进行预处理(100℃，保温1小时； 300℃，保温2小时)；经热力学计算，还原钛氧化物的氧分压至少要低于5.11×10-7Pa，结合电解过程中所用熔盐CaCl2有极强的吸水性的特点，电解装置应有较高的密封性，自行设计了一套密封性可靠的电解装置，便于实验过程中熔盐预处理和氧分压的控制；通过干燥处理预电解过程中Ar流量大约为1.5L/min、电压为2.8 V、温度为850℃、时间为2小时，电解过程中Ar流量大约为0.2L/min、电压为3.1V、温度为900℃，实验结果表明电解时间与TiO2质量密切相关，质量越大需要电解的时间越长；通过自来水冲洗—稀盐酸浸泡、洗涤—在超声波辅助作用下稀盐酸洗涤，可减少熔盐及其它杂质对电解产物检测结果的影响；最后，通过循环伏安法、计时电流法对电解机理的研究，确定电解还原TiO2制备金属钛主要经历了TiO2-TiO-Ti的过程。

The method includes the following steps: getting specific amount of knitted or unknitted natural fiber and dipping the natural fiber in the aqueous solution of silane coupling agent for 1-100min, taking out and drying the natural fiber, thus producing natural fiber with modified surface; then pressing the polylactic acid into sheet in a plate vulcanization machine; disposing 2-10 polylactic acid sheets into a die and arranging one modified natural fiber sheet between every two polylactic acid sheets; pressing and molding the sheets; in this way totally biologically degradable polylactic acid composite material can be made.

该方法为：先取一定量的经过编织或未编织天然纤维，将其浸渍在偶联剂水溶液中1～100分钟后取出，经干燥后得到表面改性的天然纤维。然后，将聚乳酸在平板硫化机中压制成薄板；将2～10片聚乳酸薄板放在模具中，且每2片之间放置1片改性的天然纤维，然后模压成型，得到可完全生物降解聚乳酸复合材料。

XLB-Y series rubbers platen vulcanizing machine is suitable for vulcanizing -molding all kinds of rubber mold press products .

XLB-Y系列橡胶平板硫化机适用于各种橡胶模压制品的硫化成型，也可用于其它热固类产品的压制成型。

In the mould press forming process,it can be directed the pr...

分析和掌握模压成型过程中树脂基复合材料的应力变化规律，可正确指导树脂基复合材料的生产。

In target ing using concrete optimum , heat preservation, humidity preservation, twice vibr ations, twice compactions, strictly controlling the temperature and so on, the a ppearance of split can be avoided and the durability of concrete can be improved .

分析和总结了预拌混凝土现浇楼板裂缝产生的原因、处理方案及防治措施，综合采用混凝土试配优化、保温保湿养护、二次振捣、二次模压、严格控温等施工措施，可有效地避免和减少裂缝出现，提高混凝土的耐久

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了