可加热

SX and EX models upgrade the interior experience with an optional Leather Package that upholsters the seats, steering wheel and gear selector plus adds heated seats to the deal.

SX和升级前模型的内部经验，一个可选的皮革包upholsters的座椅，方向盘和齿轮选择加补充加热座椅的处理。

Results N-hexane ∶acetoacetate ∶95%alcohol(12.8 ∶7.2 ∶2.2)were used as developing agent together with strong aqua ammoniae,in which the thin layer plate was saturated for 40 m...

结果以正己烷-乙酸乙酯-95%乙醇(12.8∶7.2∶2)为展开剂，用浓氨水和展开剂同时饱和40min，展开，取出晾干，以10%浓硫酸-乙醇为显色剂，70℃下加热30min，可获得分离清晰的6个有色斑点。

Lever Ball Float Steam Traps seat to increase the use of pairs of condensing water displacement, small displacement can reach large, the largest hydrophobic capacity of 100 tons / hour, is the ideal trap large heating equipment.

杠杆浮球式疏水阀利用双阀座增加凝结水排量，可达到体积小排量大，最大疏水量达100吨/小时，是大型加热设备最理想的疏水阀。

Lever ball float type steam trap condensate using two-seat increase in displacement, small displacement can reach large size, the largest drainage capacity of 100 tons / hour, is the major heating equipment, the best traps.

杆浮球式疏水阀利用双阀座增加凝结水排量，可达到体积小排量大，最大疏水量达100吨/小时，减压阀是大型加热设备最理想的疏水阀。

"There are numerous other electrically operated devices used on various cars, including the radio, a seat warmer to warm the seat before the car heater Brings the car interior up to a comfortable temperature."

在各种汽车上还有许多其它的电气装置，包括收音机、电热器、电动门锁、后窗防雾器、旅行车后窗雨刷、挡风玻璃雨刷、电眼等等。在汽车加热器给车内加至舒适的温度之前，电热器可先给座椅加温。

Plastic Injection the design process, which is designed as part of the craft-oriented establishment : Plastic Parts of the Process Analysis, Plastic Parts of the size and quality of calculation and the injection parameters set; Structural design : Surface choice cavity determination, Cavity the arrangement, gate design, lateral type pulling mechanism design, launch and reattached body identified; Core, Cavity size calculation; Die heating and cooling system computation; Mold closing high set; Injection machine parameters in the verification; The design of such a structure can be used to ensure reliable die.

注塑模中文摘要翻译成英文摘要？？？帮帮忙~~~救急啊塑料注射的设计过程，其中的设计内容有零件的工艺性编制：塑件的工艺性分析、塑件的体积和质量计算及注射机参数的确定；结构设计：分型面选择、型腔数确定、型腔的排列方式、浇口设计、侧向分型抽芯机构设计、推出及复位机构方式确定；型芯、型腔尺寸计算；模具加热和冷却系统计算；模具闭合高度确定；注射机有关参数的校核；如此设计出的结构可确保模具工作运用可靠。

The interior features electric windows, remote central locking, a heated rear window, a removable rear cross brace in safety roll cage, sport seats and a complete leather/alcantara interior.

内部功能电动窗，遥控锁，加热后车窗，一个可拆卸后方交叉支撑在安全防滚架，运动座椅以及一个完整的皮革/阿尔坎塔拉内部。

The relative humidity of the air in the drying chamber would reach to 23% in a short time at the 65℃ drying temperature for the new developed dryer.

低湿调温乾燥机空车以65℃以上加热除湿，相对湿度在很短的时间内可达2 3%。

Energy requirement for drying could be reduced by a dryer with a heat recovery device. In order to analyze the optimum operation conditions, the effect of fan speed on the temperature, airflow distribution and effectiveness of the heat recovery device was investigated in the drying system. The optimum fan speed would be at maximum speed during initial heating stage and at lower speed during steady stage in order to improve the performance.

具有热能回收装置的乾燥系统能降低乾燥所需的能量，为了分析此乾燥系统的最佳操作条件，测试其风扇转速对於乾燥室内温度、风速和热能回收装置效能的影响，归纳出风扇最佳运作应是在加热启动阶段应用最快转速，到达稳定阶段后，以较低转速可提升乾燥机的性能。

A kind medicine refining used vacuum drying box without tray, in which there are finger type heating pipe s, was introduced.

介绍一种可折卸指形加热管的无料盘药品精制真空干燥箱。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷