口

According to this curious distinction, the "active" fellator was playing a female role, while the "passive" man who was being fellated remained true to his role as a male.

在过去，特定的一些人在口交中的&主动&和&被动&方之间进行辨别，根据这种好奇的区别，主动口交者扮演女性的角色，而被动方则扮演他真实的身份即保持着他们男性的角色，这个原因字行（另外完全改变了主动方男性和被动方男性的一贯的模式，）便导致了一个荒诞的断言，那就是只有&被动&方才是真正的同性恋。

And there were set there six waterpots of stone, after the manner of the purifying of the Jews, containing two or three firkins apiece.

2：6 照犹太人洁净的规矩，有六口缸摆在那里，每口可以盛两三桶水。

Now six pots of stone, every one taking two or three firkins of water, were placed there for the purpose of washing, as is the way of the Jews.

2：6 照犹太人洁净的规矩、有六口石缸摆在那里、每口可以盛两三桶水。

And there were set there six waterpots of stone, after the manner of the purifying of the Jews, containing two or three firkins apiece.

照犹太人洁净的规矩，有六口石缸摆在那里，每口可以盛两三桶水。

And there were set there six waterpots of stone, after the manner of the purifying of the Jews, containing two or three firkins apiece.

2：6 照犹太人洁净的规矩、有六口石缸摆在那堙B每口可以盛两三桶水。

The injection time was correlated to the size of orificium fistulae, and the plugging was successful for 4 patients with less than 3 mm orificium fistulae.

注射次数以及住院时间与瘘口大小有一定的联系，瘘口小于3 mm的4例患者均一次封堵成功。

Yun-strip method, the circle-shaped bath temperature higher than the crescent-shaped article transport transport of temperature, the temperature was higher than the crescent-shaped article transport serrated Article transported bath temperature, in the 12mm flat bottom welded seal, using serrated transport of , and with the magnitude and the swinging groove on both sides of the pause, effective control of the bath temperature, so that pore size of the melt is essentially consistent with the roots do not form a welding groove tumor and decrease the chances of burn-through, no penetration has The improvement of the peace panels of the single-sided welding butt welding flat-sided shape is no longer difficult.

运条方法，圆圈形运条熔池温度高于月牙形运条温度，月牙形运条温度又高于锯齿形运条的熔池温度，在12mm平焊封底层，采用锯齿形运条，并且用摆动的幅度和在坡口两侧的停顿，有效的控制了熔池温度，使熔孔大小基本一致，坡口根部未形成焊瘤和烧穿的机率有所下降，未焊透有所改善，使乎板对接平焊的单面焊接双面成形不再是难点。

Combined with the design of injection molds and actual production,technical gists ofinjection molding design are introduced on the number of gates,flow pattern,gate position, weldline position and runner design.

结合注塑模设计和生产的实际，重点介绍了注塑模模流设计在浇口数目、流动形态、浇口定位、熔接线位置、浇道设计等方面的技术要领。

This paper analyzes relationship among the design of plastic products, raw material constitution and fluid channel design of extrusion die and elucidates the importance of their a-greements each other.

论述了塑料制品设计、原料配方、设备选用与口模流道设计间的关系，阐明了它们之间良好协调的重要性；并结合塑料熔体流变理论和实践经验，以180装饰壁板为例，分析讨论了此类异型材口模流道设计的思路和方法

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory.

本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。