口

According to the calibration information, Research and development status of automotive bus network and automotive calibration system is studied and the research significance is generalized. First of all, the collectivity precept for calibration system is designed, the calibration platform is set up based on the XCP Protocol and the calibration object is CAN bus network simulation ECUs. Then how to create the calibration system based on Ethernet and Series communication is expatiated, the communication way from computer to ECUs is introduced and the calibration system is tested. Then how to create the calibration system based on CAN bus communication is expatiated, the design and the interface programme are introduced and the calibration system is tested. At last the platform is used to calibrate the CAN bus network simulation system to regulate the simulation system's topology and communication speed to test the communication protocol's feasibility.

论文首先设计了标定系统的总体方案，以CAN总线实时仿真系统中的节点标定为研究对象，采用XCP协议建立具有串口、以太网和CAN总线三种通讯接口的标定平台；然后，具体开发了基于以太网通讯和基于串口通讯的标定系统，完成了上、下位机部分的软件设计，确定了标定系统在两种通讯方式下的数据处理方法，并分别应用两种标定方式标定下位机仿真系统的参数，让下位机仿真系统在规定的通讯协议和拓扑结构下进行仿真，对所设计的标定系统进行了调试；接着，设计了基于CAN总线通讯的标定系统，完成了CCP协议（&XCP on CAN&）的接口程序设计，并通过混合动力汽车一种拓扑结构的通讯仿真对所设计的系统进行了调试；最后，应用开发的标定系统，对混合动力电动汽车网络通讯协议进行了仿真研究，并根据实验结果进行了分析。

And formsof the three opening were very consistent when the female mandarin voles were notin the estrum.

所有的雌性个体有三个开口：外阴口、尿道口和肛门口。

There are several types of ewers: one has a dish-mouth, a broad neck,a bulging body with a concave base, a flat handle and a short, six-sided spout.

水罐可以分为很多种，一种是有碟口、宽颈、宽身、凹面罐底，扁平的手柄，六边形较短的喷口。

Around the top of chassis to allow a certain space, in particular, attention should be paid to the various chassis air intake and the exhaust port.

机箱的周围的顶部要留有一定的空间，尤其要注意机箱上的各个入气口和排气口。

It's a small thermal exhaust port,right below the main port.

是个反应炉排气口，就在主排气口的下方

Figure 1 is the pump suction and exhaust rotor is located just off the termination of position, suction ports and exhaust ports have been sealed rotor sidewall.

图 1 是泵转子刚好位于吸气和排气终止位置，吸气口和排气口被转子的侧壁封住。

Exhaust port to allow the biggest obstacle to Por value"("exhaust port Por is defined in VM series of detailed parameters) this parameter is the calibration of the exhaust pump capacity, so that we can use technical means to determine the strict selection is appropriate.

排气口允许最大阻力 Por 值&（&排气口Por的定义参见VM系列详细参数）这一参数就是标定泵的排气能力，让我们可以用严格的技术手段确定选型是否恰当。

Results All of the tumor was exsected successfully, the average inosculating time was 28 min and average total operation time was 132 min. The postoperative complications was few and no anastomotic stoma fistula, anastomotic stoma narrow, stomal ulcer or chest gastric emptying block was occurred. The average length of stay after operation was 9.7 days.

结果 肿瘤均顺利切除，平均管状胃吻合成形时间28min，平均总手术时间132 min；术后并发症少，无吻合口屡或狭窄、吻合口溃疡、反流性食管炎及胸胃排空障碍发生；术后平均住院时间9.7d。

Not only the traditional feed mixer the efficiency is not high, moreover the ingredient precision is low, the energy consumption quite is big, already could not satisfy the feed industry development request; The turn over type two axle thick liquid leaf type mixer has the mix cycle short, the mix effect good, the energy consumption...

翻转式双轴浆叶式混合机具有混合周期短、混合效果好、能耗低、出料干净和对不同物料混合的适应性强等优点，它把入料口和出料口合二为一，卸料速度快，残留量小，可使物料进行多方位的复合运动和在失重区域内的自由运动，避免了比重和颗粒度差异较大的物料组分在混合中产生偏析与再度分级现象，确保了混合均匀度。

The models of cutting edge, the flute of ball end milling cutters with spiral flute of different section, and the section profile and relative feed speed of grinding wheel are provided.

分析了三种不同定义的螺旋刃口曲线的异同和与优劣，给出了二轴联动数控加工时不同截形的螺旋沟槽球头铣刀的刃口、沟槽及砂轮截形、相对进给速度等设计模型，并通过实得沟槽及计算机模拟结果进行了验证，认为借助该模型可获得较理想的球头回转铣刀。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。