变形的

The results showed that plastic deformation at both -70℃ and 180℃ made the dislocation density of AISI304 stainless steel increase with the increase of deformation. Martensite phase transformation was induced for deformation at -70℃, whereas it was not at 180℃. As the dislocation density increased, the breakdown potential of AISI304 stainless steel's passive film became a little more positive. As martensite phase content increased, it became more negative and pitting corrosion resistance decreased.

结果表明：加热180℃和低温-70℃条件下塑性变形均使AISI304不锈钢中位错密度随变形量增大而增加，AISI304不锈钢在-70℃条件下塑性变形时部分奥氏体相转变为马氏体相，而在180℃条件下塑性变形时不发生马氏体相变；位错密度的增加使AISI304不锈钢钝化膜的击穿电位略微正移，而马氏体相的增加使击穿电位呈负移趋势，材料耐孔蚀性能降低。

For instance,(1) mountain terrain map: displaying the terrain and topography, is 3D emulation of earth's surface, is convenient for customer to look into the physiognomy, and check the data of input;(2) contradistinguish map of mine well: displaying opposite position relation of the earths surface and workface, user can analysis surface movement and distortion value at every positions of the workface with the map;(3) 3D prediction model: displaying workface, survey dots, survey lines, terrain, movement and distortion in a same map with 3D graphics, revealing the relations of every elements' position;(4) isoline graphics: displaying the value of height, subsidence, incline, movement and distortion with different colors, and giving the value of every color at the side of the map;(5) color cloud diagram: revealing every targets with colors, coloring every point in the map with the color corresponding the value of height, subsidence, incline, movement and distortion and form transitional color in color cloud diagram.

通过井上下对照图，用户可以分析工作面的各个位置的地表移动变形值；（3）三维的预计模型：采用3D形式同时显示工作面、测线、测点、地表地形、地表移动及变形，显示了各要素的空间相对关系；（4）等值线：对地表高程、下沉、倾斜、曲率变形、水平移动和水平变形等各个分量以等值线方式显示。

The results show that dynamic softening is easy to occur in these ingots and flow stress becomes steady finally; the material constants of hot deformation are procedural parameters that stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q are all increased with strain increasing, while stress exponent n is decreased gradually; the values α and m of the alloy homogenized are the biggest and the value n is the smallest, dynamic softening effect of the alloy is the most obvious, which can deform evenly; influence of strain on the value Q of the alloy homogenized is a little and the average value of Q is only 176.5kJ/mol, so the alloy is easy to deform; the alloy matrix shows the regular recrystallization grains when the strain is 50%; dislocation cell structure re-formed in the grains with increase of strain.

结果表明：经不同处理的Al-1Mn-1Mg合金均易发生动态软化并最终呈现稳态流变特征；热变形材料常数是过程量，随应变量的增加，应力水平参数α、应变速率敏感性指数m和热变形激活能 Q 随之增大，而应力指数 n 则逐渐减小；均匀化退火后，铝合金的α和m值最大而n值最小，动态软化效果最明显且变形均匀，在该状态下，铝合金的 Q 值受变形量影响小，平均仅为176.5kJ/mol，易进行热变形；当应变量为0.7时，基体呈现规则的再结晶晶粒组织，随着应变量的增加，晶内重新形成了位错胞结构。

With respect of slab lateral cambering of hot rolling sizing press,the analysis shows it is the temperature difference on both sides of the slab that causes different resistance in metal's plastic deformation,which makes metal deform at different speeds.

针对热轧SP定宽轧制的板形侧弯问题，经分析指出：板坯两侧温差造成金属塑性变形抗力大小不相等，从而使金属变形速度不同，变形速度快则相同时间内移动的金属量多，最终使变形快的一侧向变形慢的一侧弯曲是板形侧弯的形成机理。

The distortion measurement system of the ship was introduced,the characteristics of aggregative processing system were compared with that of distributed processing system.

介绍了船体变形测量系统，对分布处理式变形测量系统与集中处理式变形测量系统的特点进行了比对，指出了新型变形测量系统的技术优势。

The thesis toke problem of deformation and destroying of the earth mass as it's invention, integrated the earth mass's existing environment, ingredients and macrostructure, discovered mechanism of deforming and destroying, made clear the relationships between those.Through outdoors samples, indoors examination surface wave testing and audio wave testing ,do some research on physical, mechanical, chemical, disintegrative and dynamics property of stuff of earth mass and proposed four kinds of earth mass's stuff formed type;under the guidance of theory of dominant structural surface and adopting precision measurement of structural surface, proposed three dominant kinds of structural surface assembling;based on those , proposed four types of earth mass's deformation and destroying, carried out rationed estimation of stability on four types, then definite the characters of deforming and destroying and controlled relation between environment , stuff, macrostructure and deformation and destroying of mass earth, and breakthrough ordinary principle about soil's deformation and destroying, further proofed the theory of earth mass cybernetics's popularization

本学位论文针对台地危险土体的变形破坏问题，将土体的赋存环境、土体物质组成和土体宏观结构的研究紧密地结合，阐明了土体变形破坏的机制，明晰了土体变形破坏与土体的赋存环境、土体材料组成、土体宏观结构三要素之间的关系，并从土体的物质组成的角度，以野外取样、室内实验、现场面波、声波无损伤测试为手段，研究了土体物质的物理、力学、化学、矿物、崩解性、动力学性质，提出了研究区内土体物质成分的四种组合形式；以优势结构面理论为指导，以结构面的精确测绘为手段，通过统计、归纳与分析，提出三种有利于台地危险土体变形破坏的优势组合形式；据此提出了具有广泛代表意义的台地危险土体变形破坏的四种模式，并对其进行稳定性评价，从而明确了危险土体的宏观结构对变形破坏的控制作用，映证了土体结构控制论。

Equiaxed and bigger grains are produced after C.P.Ti is deformed under the high temperature. Besides, many tiny subgrains were found in some of the metallurgical structure. The dislocation reaction caused by the deformation under the high strain rate generates ductile cellular metastructures, while the equiaxed cellular metastructures are generated under the low strain rate. The metallurgical structure of TC4 alloy including lath-shaped hexagonal martensite and trimetric martensite only exists in the higher temperature. The homogeneous, tiny and reticular grain shown after extreme high temperature deformation.

在高应变速率下变形引起的位错反应形成拉长的胞状亚结构，而低应变速率下变形则形成等轴的胞状亚结构；TC4合金在特高温变形条件下其金相组织呈网篮状，显微组织几乎全部为均匀细小的晶粒，同时出现了板条状六方马氏体；在温度尤其高的情况下还形成了斜方马氏体，变形引起的位错反应形成六方位错网络，在1200℃以下的变形易产生孪晶。

GPS location technology is first used in Construction Bank building of Xiamen. It has built the control network of floor construction; Precision of location and setting out can meet the needs of high-rise building construction; Deformation curve reflects the law of sunshine deformation; Frequency spectrum chart of kinematic deformation monitoring reflects kinematic feature and the law of deformation.

GPS定位技术在厦门建设银行大厦工程的首次应用，建立了施工楼层的GPS定位控制网，其定位放样精度完全能满足高层及超高层建筑施工的要求；日照变形监测的变形曲线，反映了建筑物的日照变形规律；动态变形监测的频谱图，反映了建筑物的动态特征和变形规律。

In this thesis we analyzed and summarized the anti-deformation function of frame construction in ground deformation -area.

对地表变形区框架结构的抗变形性能进行了分析、研究和总结，归纳了框架结构抗变形设计的原则及其措施，并提出框架结构抗变形和抗震双重设计理论及其研究思路。

A correlation of the experimentaldynamic response of the vessels with the theoretical finite element calculations ispresented and discussed.1 The response of the end caps is dominated by transverseand torsional deformation of the plates.The membrane strain is negligible compareto the lateral strain.2 In the lengthwise direction of the inner cylinder,themembrane strain has the same magnitude as that of the bending strain. But for theouter cylinder,the former is much smaller than the later at the same direction.3 Forboth the inner shell and the outer shell,hoop strains are primarily due to themembrane deformation.The amplitude of the circumferential flexural strain isconsiderably small.4 Peak strains in the vicinity of the connection portion of theend caps and the shells are very high.This is important to assess the safety of thecontainer in case of repeated use or tests.5 The applying load to the end cap isdifferent from that to the inner shell plate, but peak stains and nodal displacementsof these two structural parts are nearly the same.It can be inferred that the dynamicresponse of the end cap is greatly affected by the structural vibration excited by theimpulsive loading.

结果表明：1在本文所考虑的载荷水平下，平板变形以板的横向弯曲和扭曲为主，中面应变幅值比较小。2对于内容器，其纵向变形中弯曲应变和中面应变大小接近；而对于外容器，其纵向变形以弯曲为主，中面变形比较小。3内、外壳体的环向变形主要是中面应变，弯曲应变分量很小。4平板和壳体连接处应变很大，这对于多次使用或实验时评价结构安全有指导意义。5尽管内筒底板和大封头上的作用载荷有一定差别，但应变峰值和节点位移峰值基本相近，这说明脉冲载荷激发起来的结构振动对封头的动态响应有很大影响。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。