变形的

At last, the error curve surface of gear profile is obtained by combining bending deformation and contact deformation.

文中首先将刀齿和轮齿抽象简化为力学模型，分析其受力状态，并运用三维有限单元法计算各节点的弯曲变形量，建立切削力与弯曲变形的关系。

In the respect of welding distortion control, two kinds of aluminum alloy sheets are used: LY12CZ and LF5, and welding distortion experiments using work-pieces with large dimensions are performed in finger-shaped fixture designed by us.

在焊接变形的控制研究方面，采用LY12CZ、LF5两种铝合金薄板，在自行设计制造的琴键式夹具上进行了大板焊接变形试验。

The flow stress increases with increasing the strain rate, and decreases with increasing the deforming temperature, which can be described by a constitutive equation in hyperbolic sine function with the hot deformation activation energy of 209.84 kJ/mol, and can also be described by a Zener-Hollomon parameter.

该合金热压缩变形的流变应力行为可用双曲正弦形式的本构方程来描述，也可用Zener-Hollomon参数来描述，其变形激活能为209.84 kJ/mol。

In this article a method based on edge extraction, linear image transformation and histogram modification is proposed to address the mentioned problem.

针对图像变形问题，我们分析了扫描图像变形的几何模型，提出了基于边缘提取和线性变换的图像纠正计算公式。

The strong deformation gneisses and mafic rocks have the stretching lineation, the ultra-plastic flow mechanisms of the hornblendes and plagioclases.

强变形的片麻岩和镁铁质岩石发育拉伸线理，角闪石和斜长石表现出的动态重结晶、超塑性流动变形机制。

Detailed study of the metamorphic mylonite of the Yangkou UHP shear complex has revealed that the deformation proceeded at ca.

项目深入研究了仰口超高压韧性剪切混杂岩的变形温度和压力在大约800 C，大于24千巴，确定了其超高压变形的性质。

A continuum model was established by introducing Newton stress formula into the elastic-plastic model to describe the deformation behavior of material in bonding zone. Based on the model, the mechanism of plastic deformation and the influence of detonation velocity on plastic deformation were analyzed and compared with experiments.

该文引入牛顿应力公式到弹塑性模型，以近似描述结合区材料行为，建立了连续介质模型，对波状结合区的塑性变形及爆轰速度对塑性变形的影响进行计算分析，并与试验结果对比。

In order to cope with the huge deformation of the highlystressed phyllite ground in the ridge section of Wushaoling tunnel, the construction program is constantly optimized, the construction technology is persistently improved, standard time duration is determined for each construction step and strict construction organization management is performed.

针对乌鞘岭隧道岭脊段高地应力千枚岩大变形，通过对施工方案不断优化，对施工工艺不断改进，并制定各工序标准耗时，同时进行严格的施工组织管理，得到了在高地应力条件下能较好控制软岩大变形的一整套快速施工技术。

If a body is deformable, as all are to some extent, the deformation depends upon the point of application of the force

如果一物体是可以变形的(所有物体都或多或少可以变形)，那么这种形变就取决于力的作用点。

So that the factory radically developed the key technology of uneven pressboard water content, and the deformation due to higher content and stress deformation of pressboard, and its products can take place of imported pressboard completely.

从根本上解决了纸板水分含量不均，含量偏高而造成的翘曲变形及纸板应力变形的关键技术，其产品完全可以取代进口纸板。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。