变形的
- 与 变形的 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
This paper studies the mesh morphing in two aspects, one is the morphing algorithm of planar triangular mesh based on the convex combination.
另一种是基于角度插值的三角网格变形算法,这是一种仅通过插值角度来实现任意网格变形的方法。
-
This paper presents the method of curve deform which is based on the concept of the energy of deform curve.
本文提出了基于变形曲线能量的概念,进行曲线相似变形的方法。
-
ATTENTION: For the deformer's attribute structure has changed, scene files using the old version of the deformer may not load correctly in some cases.
注意:对于变形的属性结构发生了变化,场景文件使用了旧版本的变形可能无法加载在某些情况下正确。
-
Mechanical twinning is strongly grain size and texture dependance.
研究结果表明,镁合金在室温变形条件下,孪晶在变形的过程中发挥了重要的作用。
-
Using the simple caculation,ANSYS analysis caculation and testing may obtain the quantity of angle distortion based on the analysis of producing the spring distortion when the compressor worked with received the load.
分析压力机在承受负载时机身产生弹性变形的基础上,分别利用简化计算,有限元分析计算和测试获得角变形量并进行对照比较,提出3种方法存在的差异。
-
Hexed heroes cannot purchase items when hex wears off without leaving the area around the shop and returning.
被变形的英雄在变形时间过后,在商店区域不能购买物品。
-
This paper using the FEM software Marc, for the 50 and 60 degree V groove of flat plate butt joint simulate the one-layer and three layers welding, finish each welding and cooling it down to room-temperature then start the next welding true represent process and get the temperature field, residual deformation and welding residual stress, according to the theory analysis and empirical equation verified the temperature field and residual deformation all correct, comparison with experiment verified the welding residual stress regularity and correctly.
本文利用有限元软件Marc,对开60°和50°V型坡口的平板对接接头,动态的模拟了单层单道打底焊,焊完一道后让试件冷却到室温以及单层单道满焊,每焊完一道后让试件冷却,然后再焊下一焊道,道间温度≤200℃,在以此为初始边界条件下开始下一道的焊接,真实的再现了焊接过程,得出了温度场,残余变形和残余应力场的分布规律,根据理论分析及经验公式验证了温度场以及残余变形的正确性,角变形的大小,这些结果与数值计算相吻合。通过与实验测得的残余应力进行比较,验证了焊接残余应力的分布规律及模拟的正确性。
-
Sculpt deformers are spherical objects which create rounded deformations.
造型变形的变形而产生圆形球状物体。
-
Using cold rolling spinning technology, this technique is a complex course which combines plastic deformation and flow deformation.
三、生产工艺:利用冷轧制旋压技术生产,它是集塑性变形和流动变形的复杂过程,技术水平较高。
-
The results show that reversible deformation values and welding sequence make a great effect on the welding deformations.
结果表明反变形量和焊接顺序对焊接变形的影响程度较大。
- 推荐网络例句
-
Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.
Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。
-
I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.
我来只是现在,'歼灭战perfuming自己与胡努特,那麼,他来到和SAT 。
-
The shamrock is the symbol of Ireland and of St.
三叶草是爱尔兰和圣特里克节的标志同时它的寓意是带来幸运。3片心形叶子围绕着一根断茎,深绿色。