变形性

This algorithm is the linear combination of the discrete Conformal mapping and the discrete Authalic mapping.

它是离散保角映射与离散保积映射的线性组合，兼有二者的优点，如鲁棒性与低变形。

Because of the problem of convergence, the key techniques to complete the one step simulation were explored thoroughly. The geometry mapping method based on finite element model and inverse deformation was developed to get the approximate initial blank for one step simulation. The effective selection of convergence factor in Newton-Raphson method was studied. The divergence criterion in iterative process for one step simulation was put forward. Also the countermeasure to ill equations coefficient matrix was studied.

由于存在收敛性的问题，本文重点研究了一步模拟方法计算机实现的关键技术：提出了基于有限元模型的几何映射方法和反向变形方法来确定初始毛坯的近似解，研究了带收敛因子的Newton-Raphson方法中如何高效地选取收敛因子，提出了一步模拟迭代求解过程中的发散准则，并研究了病态方程组系数矩阵的修正方法。

The origin、 development and present state of the container ship2. The deformation characters and collapse mode of the container ship3. The basic theory of thin-walled structural mechanics: The bending of the thin-walled beam; The unconstrained torsion of the thin-walled member bar; The constrained torsion of the thin-walled member bar with opening; The constrained of the thin-walled member bar with closed port.4. The calculation of the warp stress in the container ship based on the thin-walled structural mechanics theoryModeling of the hull ladder calculation based on referred mechanics theories of thin-walled member bar, calculation of crankle character of the each section, such as sectional coordinates、 Free twist shear flow、 secondary shear flow、 bend shear flow and so on.

本文主要包括下述六个方面的内容： 1 集装箱船的起源、发展和现状 2 集装箱船变形特征和破坏形式 3 薄壁结构力学的基本理论◇薄壁梁的弯曲；◇薄壁杆件的自由扭转；◇开口薄壁杆件的约束扭转；◇闭口薄壁杆件的约束扭转 4 利用薄壁结构力学理论计算集装箱船的翘曲应力建立船体阶梯计算模型，利用薄壁杆件力学中相关理论，求解各断面单元的弯扭特性，包括：扇性坐标、自由扭转剪流、二次剪流、弯曲剪流等。

In addition, there is delamination removal at weak interface due to decarburization.

普通涂层的磨损机制为微切削；纳米涂层在轻载(10 N)下，以塑性变形为主要磨损机制，随载荷增加至30 N，纳米WC粒子不能起到阻抗陶瓷球对磨副的磨削作用，而是随粘结相一起被去除，同时由于纳米涂层脱碳导致的层间结合薄弱，在滑动磨损中易发生成片剥落，耐磨性大幅下降。

Connected with the actual situation of slope, the rockmass instability index is given, which is then compared with predictable ratio of practical deformation slope.

结合边坡实际情况，计算出岩体不稳定指数，并同观察实际变形边坡得出的可预报性估值进行了比较。

The deformation of slope caused by change of ground water level was investigated by adopting a fully coupled procedure and the state-dependent dilatant sand model.

本文采用完全耦合有效应力分析程序和与状态相关的剪胀性砂土模型模拟斜坡因地下水位变化而发生的变形。

Welding is carried out in such a way that the resulting temperature increase of the blade (2, 35) be so reduced that the hardened steel sheet (2, 3) is not disadvantageously deformed, nor loses its hardness or wear-resistance.

用这种焊接所得出的刀片（2、35）温度的升高是相对低的，这样硬化金属板材料（2、35）即不受到变形的不利影响也会在硬度和抗磨损性方面遭受巨大损失。

At 8 weeks postoperatively, the grafts were mostly substituted by new cells, and the artificial ligament was completely parceled by the synovial membrane, but there were still some gaps; The combined tendon exhibited no loose or disfiguration, the infiltrative inflammatory cells disappeared. The cells in grafts were close to normal cells in anterior cruciate ligament, but fibrocytes arranged in disorder and fibers showed a verticality.

移植后第8周，移植物大部分组织被新长入的细胞替代，人工韧带被滑膜完全包裹，浸润的炎症细胞基本消失，部分接触面已融合，但部分面仍有间隙；联合肌腱无变形和松弛，移植物内细胞形态，数量接近正常前交叉韧带，但纤维细胞排列杂乱，纤维有了一定的纵向性。

Immediate postoperative complications within one week include perinasal swelling (60 patients), perinasal pain (32 patients), perinasal ecchymosis (26 patients), periorbital swelling (6 patients) and epiphora (3 patients). Most of the complications disappeared within 3 months except intermittent tingling sensation in one patient and residual deformity in three patients.

手术后1周内并发症包括鼻周肿胀60名，鼻周疼痛32名，鼻周瘀青26名，眼周肿胀感6名，溢泪3名。3个月后仍存在的术后并发症包括间歇性刺痛感1名以及矫正后之残余性变形3名。

It is suggested that the classification of extensional fold s incorporates both axial trend and mechanism of folds.

伸展褶皱是张性盆地区构造变形的重要组成部分，其分布相当普遍，多属于与正断层相关的褶皱。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。