变形

Analyzing and simulating of the deformation law of the ceramic downspout product after overcoming the shortage of powder material models in the software of MSC. MARC. It shows out the important effects of various factors and the shape of mandril during the process. And it is obvious that the shape of the top mandril has more effects on the process than the bottom.(3) Showing out the important effects of model figure on the flowing of powder and the forming of low-density fields from the analysis. After changing the top of the mandril into spherical shape, an improving model is putting out so that the distribution of stress and strain turns to be even and proper and that the flow rule of powder grains is better.(4) Calculating of the dimensional precision and the cutting ratio of the product and analyzing of the effects of such factors as rubber aging, loading process, mandril, friction etc. on the cutting ratio.

MARC存在的粉末材料模型方面的设计缺陷后，对连铸水口粉末成形件的变形规律及影响因素作用进行了模拟分析，指出芯棒形状对成形件的变形有较大影响，并且芯棒顶部形状与芯棒底部形状相比，对粉末变形有更大影响；(3)分析了成形件出现低密度区域的原因，指出模具形状对粉末流动以及粉末成形件低密度区域的形成有重要作用，提出了密度分布优化改进模型：改进模具顶部形状，并将芯棒顶部设计成球面后，粉末成形件顶部区域的应力、应变分布更加均匀、合理，粉体颗粒流动情况明显改善，低密度区域明显缩小；(4)计算了成形件的尺寸精度及切削率，并指出除模具形状的影响外，充填密度、橡胶模具老化、加载工艺等其他因素对总体切削率也有相当的影响。

In this article, based on the mechanic model of throttle-slice, the bend deform differential equation is founded, the formula and coefficient of elastic throttle-slice bend deformation are created.

通过减振器节流阀片的力学模型，建立了节流阀片弯曲变形的微分方程，得到了阀片弯曲变形系数和在任意位置的弯曲变形计算公式。

The deformation of the paper consists of elastic deformation and plastic deformation.

纸张的变形可以不合为不不弹性变形和不弹性变形。

Researches on the earth's land surface processes and the geological environment essential factor and its dynamic mechanism have demonstrated that only with the equilibrant system of the low-temperature and low-stress and the scattered as well as dense multi-grains, the boundary condition for the slow, long-term and intermittent pulsation action can meet the formation conditions of such a rock deformation structure.

通过物理模型分析和试验变形比对等综合材料证明，变形砾石是遭受了既密集、又分散、还具有同时发生作用的长时期的多边界外力条件及平衡力系，内部形成破裂其应力传递过程和性质改变与变形形迹转变及其做功连续扩展，是由低于疲劳极限的具有脉动性作用微弱应力造成的。

According to the viewpoint that the thinnest part of the deforming metal is usually the important and decisive part of the deforming force , the influence of the bridge size of the fash slot on the die forming and the deforming force is analyzed.

通过坯料在模锻型腔中的压挤成形过程，模拟开式模锻中飞边槽对金属充满型腔的作用，根据"变形金属最薄的部分常常是决定变形力的重要部分"这一观点，分析和探讨飞边槽桥部尺寸对模锻成形及变形力的影响，提出对高度较小、直径较大的齿轮以及复杂模锻件设计方法的改进，以提高该类锻件的模具寿命和生产率。

The effect of surface friction on the structure of front and frontogenesis is investigated by using the cloud model in which the large-scale deformation field is taken into consideration.

利用加入大尺度变形场作用的非静力模式，研究了地面摩擦对锋生和锋面结构的影响，在变形场锋生条件下，对不同模式格距、不同湍流参数化方案、不同变形场强度、考虑与不考虑地面摩擦等情形进行了比较，在考虑地面摩擦拖曳作用后得到了类似重力流结构的边界层锋面特征。

It is concluded that frost heaving is much more than thaw settlement, it is in accordance with observation results along Qinghai-Tibet highway.⑥Differential equation of heat transfer with phase change is derived in this paper.

通过模型试验，得出变形场受温度场控制的结论，并在多个冻融循环中，存在着一个斜坡后继变形的"温度门限"，控制着斜坡变形的进一步发展。

For deformation monitoring in dam, simultaneously survey must be taken to physical quantity as well as the distortion value, then functional relation between them can be established by means of statistical regression analysis method that is called regression analysis method.

对大坝进行变形监测，必须同时测量产生变形的各种物理量以及变形的结果，结合统计回归分析的方法建立两者之间的函数关系，这就叫做回归分析方法。

The test results also indicate that separating RC ultra short column into separated columns (shear span to depth ratio higher than 2) by gapping longitudinally at the middle of ultra short column can improve the ductility and deformation capacity of the columns effectively.

不设剪力连接件的SRC超短柱的破坏模式为黏结破坏，与RC超短柱相比，其抗剪承载力和变形能力并无明显提高；设置剪力连接件的SRC超短柱的破坏模式为斜压破坏，其抗剪承载力和变形能力显著提高，但构件的变形能力仍然难以满足现行抗震规范要求。

The method of simulation deformation about hanging wall with the fault-related folding model by the premises of fault geometrical parameter is go by the name of structure forward.

构造反演是指利用地层变形形态反推使之变形的断层的几何参数；构造正演是在已知断层几何形态的情况下根据断层相关褶皱模型模拟相应的上盘地层变形过程，两者是一对相互可逆的几何推算过程，是构造建模的重要组成部分。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。