变均匀

The results showed the masterbatch prepared from EVOH/compatibilizer,HDPE and EVOH/compatibilizer(4:1)was used as barrier masterbatch,the prepared material had an obvious and homogeneous toothlike structure,having good barrier property.

结果表明采用EVOH／相容剂和HDPE、EVOH制备的母粒能明显改变材料的流变性能，当采用EVOH／增容剂为4／1的阻隔母粒，所得材料的结构为大而均匀的片状形态，具有优异的阻隔性。

The unetched specimens were instantly observed by QUANTA-400 environment scanning electron microscope,scanning tunnel microscope and optical microscope,respectively.The results show that the surface relief will be found during the bainite transforming and will be in the shape of "Λ".The formation of bainite surface relief is to ...

不经浸蚀，分别采用QUANTA-400环境扫描电镜、Nanofrist-1000扫描隧道显微镜和光学显微镜观察试样，发现，贝氏体相变过程中产生了表面浮凸，表面浮凸为&帐篷形&，并认为贝氏体表面浮凸的产生，是由于过冷奥氏体转变为贝氏体时比体积增大，且试样表面层体积膨胀不均匀造成的。

Effect of partiality degree material physics character change and ununiform of winged slice temperature on transfer heating of circle core pipe rectangle winged slice was examined.

初步考查了偏心度、材料变物性和翅基温度的不均匀性对偏心圆芯管矩形翅片传热的影响。

The results show that the alloy undergoes obvious plastic elongation, the specimen fractures into four sections and the diameter changes from 16 mm to 12 mm. The fracture surfaces distribute randomly well developed and partially developed veinal patterns. The deformation behavior of alloy is non-Newtonian flow behavior. About 3% amorphous matrix of extruded specimen transforms crystal, the crystal particles with size of 10-20 mm are precipitated in the amorphous matrix, the thermostability of the extruded specimen was lowered. The failure of the alloy is mainly attributed to non-uniform viscous flow under high strain rate resulting from the hydrostatic extrusion process.

结果表明：非晶合金在高应变速率下产生了明显的塑性变形，直径从16 mm变为12 mm，断裂为4段，且样品断口上随机分布着充分发展与未充分发展的脉纹式切变带，由此可看出非晶合金的变形为非牛顿体变形行为；挤压后的样品约有3％的非晶相发生晶化，在非晶基体上析出10～20 nm的纳米晶粒，导致挤压后非晶合金的热稳定性降低；静液挤压高应变速率变形条件使非晶合金产生非均匀流变，是造成非晶合金断裂的主要原因。

The result is cast iron cookware that distributes heat evenly, while browning and caramelizing food to perfection.

结果是均匀地分布热，当对完美时的变褐的和变成焦糖的食物的生铁炊具。

With the increase of temperature, the density of dislocation decreases, and the recrystallization grains are coarser.

随着变形温度的升高，位错密度明显下降，晶粒明显长大，组织也变得更为均匀。

Although most studies dealing with the modification of semi-crystalline polymers with inorganic particles reported embrittling effects by comparing ultimate elongation and impact strength of composites materials with those unfilled resins, some researchers showed that the enhancement of toughness in rigid particle filled polypropylene and polyethylene, in which high filler content is generally required (the volume fraction is about 20%).

然而，由于纳米粒子极易聚集的特性和聚合物熔融状态下呈现的高粘度性质，使采用常规的熔融共混技术制备均匀分散的纳米复合材料变得极其困难。

My skin tone was immediately evened out and it also neutralized the redness from my blemishes.

我的肤色立即变得均匀，也能中和我脸上的暗疮红印。

The results show that grains at core are coarser and deformation bands are observed at surface,while microstructure both at core and at surface is composed of bainitic ferrite laths with high dislocation density and interlath cementite or residual austenite.Good uniforinity in h...

结合NQP钢连续冷却时的相变特点，分析其截面硬度波动在±1.5HRC内的原因在于其有较好的贝氏体淬透性，模块整个截面上都得到了均匀的贝氏体组织，贝氏体板条宽度和位错密度的差异使得其表层硬度稍高于心部。

METHODS: After Feulgen staining, 40 paraffin samples of astrocytic tumors were observed about DI and 5cER by image analysis, MRI appearances were reviewed, including edema around tumor, clearity of boundary, equality of MRI singal, enhancement of tumor, shift of medline, necroses and cyst, then compared them with pathological grade and survival rate.

40例星形细胞肿瘤石蜡标本经Feulgen染色后，用图像分析仪检测其DNA指数及超5倍体率(5cER)；复习患者MRI表现，包括：瘤周水肿程度、边界是否清楚、信号是否均匀、病灶是否明显强化、病灶是否过中线、有无囊变坏死6项指标，与肿瘤病理分级诊断及生存率相比较。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。