变化范围

This essay is going to do the comparison from five parts : construction ,scope of application , Classification ,Definition, Relevant accounting entry. Then , I do some analysis about the influence of the new leasing Standard Change and some problems which should be concerned in the process.

本文主要从结构的比较、适用范围的比较、分类的比较、定义的比较和相关会计处理的比较五大部分对新旧租赁会计准则进行了比较，进而对新旧租赁会计准则变化产生的影响以及执行租赁准则应注意的问题进行分析。

This article analyzes the key criteria under the new accounting statement and the scope of the changes and the impact on listed companies.

本文重点分析了新准则下会计报表的并范围的变化及对上市公司的影响。

The reservoir traverse quite be stable, but the relative property is quite strong, by the southwest to northeast, the characteristic of the porosity growth is degression tendency. On longitudinal it is the permeability variation in a big way, and the aerosphere scope small.

研究区须家河组储层横向分布比较稳定，可对比性比较强，由西南向东北，孔隙度发育有递减的趋势；纵向上具有渗透率变化大、气层范围小的特点。

Examinations of steady status and analysis of dynamic experiments have been conducted on Band-Tube evaporator and Parallel-Flow condenser using R134a refrigerant. The steady examination show that the model error was under the allowable error, The inlet mass and enthalpy disturb experiments indicate that the subsection model ,be good at reflecting the change of parameters of the heat exchanger, accord with the basic principle of thermodynamics theory and the actual work status.

在进行仿真试验时，以使用R134a作制冷剂的管带式蒸发器和平行流式冷凝器为对象，完成了稳态仿真计算、试验和动态仿真分析，稳态计算结果和试验数据对比表明，其误差在允许范围内；进口质量和焓值的扰动试验结果表明：本文所建的区段式换热器仿真模型，能很好的反映换热器性能参数的动态变化，与系统热动力学理论和冷凝器、蒸发器的实际工作过程基本一致。

At the temperature of 60℃ the variating of performances was allowable for space application.

在60℃高温下，器件的性能变化在空间应用的允许范围之内。

But Sinusoidal alternating current is the most widely used now.

不同变化形式的交流电其应用范围和产生的效果也是不同的。

The model has a good prediction at lower temperatures, while it is bad at higher temperatures where the solid phase was no existing and peptide product would be hydrolyzed because of the presence of amidase activity.

这是因为该模型未能考虑在偏高温度范围内酰胺酶活性对肽产物的水解作用，但这并不影响该模型对低温下肽合成产率变化的良好的预测性能。

The 1.5x zoom lens has enough range to move back and forth from 2.35 to 16:9 if the user wishes to set up a 2.35 CIH system with zoom changes rather than the anamorphic lens.

的1.5倍变焦镜头，有足够的范围，摆脱2.35来回16时09分，如果用户希望建立一个2.35 CIH病毒系统变焦的变化，而不是变形镜头。

When be admitted to hospital, mix after be admitted to hospital by clinical nerve function the degree that be short of caustic gives a mark 4 weeks[2] , cent progresses significantly, progress, invariant with death 4 class. 1.2 determine methodological research target (inside the 24h after be admitted to hospital) Yu Qingchen is hollow 4ml of blood of the vein that collect ancon, detached serum - 70 ℃ are saved wait for measure. Hs-CRP reagent is product of German LEADMAN company, day stands - 7600 full automatic biochemical appearance compares chaotic, referenced limits mg/L. Know exactly about sth of place of 1.3 statistical methods is occupied all classics SPSS...

入院时和入院后4周按临床神经功能缺损程度评分[2]，分显著进步，进步、无变化和死亡4级。1.2测定方法探究对象(入院后24h内)于清晨空腹采肘静脉血4ml，分离血清-70℃保存待测。hs-CRP试剂为德国LEADMAN公司产品，日立-7600全自动生化仪比浊，参考范围mg/L.1.3统计学方法所有数据均经SPSS。。。

The research result shows that the best fuel delivery advance angle of diesel engine used has been changed; with the first cylinder as the standard, the deviation of the fuel delivery advance angle between the first cylinder and other cylinder surpasses allowed range; the smoke emission and fuel consumption can be decreased and delivering fuel to each cylinder at the right time can be assured, through the selection and adaptation of fuel delivery advance angle .

研究结果表明：使用后柴油机的最佳供油提前角发生了变化；以第一缸为准，其它缸与第一缸之间的供油提前角偏差超出了允许的范围；实行供油提前角的调配可使各缸在正确的时刻供油，减少排放，降低油耗。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐