变位曲线

Based on the involute's basic principles and theoretical formulas, input the involute's formulas of cartesian coordinates into the equation editor, accordingly create the precise involute of gear's contour. Based on the formula of helical gear's parameters, accurately create a curve of tooth profile. Create the chraceristics of helical gear by ordering of swept blend and array.

依据渐开线生成的基本原理和理论公式，在方程编辑器中输入渐开线的笛卡尔坐标方程，从而生成精确的齿轮轮廓渐开线；根据角变位斜齿轮各参数的计算公式，精确创建了齿廓曲线；利用扫描混合和阵列命令创建斜齿轮的轮齿特征。

This paper studies on the ground settlement due to the deformation of the supporting structure. The normal distribution and parabola function are used to fit the curve of ground settlement and the estimating formula is deduced gradually.

本文主要对由于支护结构变位而引起的地表沉降进行了相关研究，利用正态分布及抛物线函数拟合了地表沉降曲线，并推导出沉降的估算公式。

Finally, a practical seismic analysis method is presented. Through a reasonable assumed distribution of lateral forces, the capacity curve can be derived from the story shear-displacement curves. And by using equations suggested by ATC-40, the corresponding capacity spectrum, period, damping ratio and PGA can also be obtained. This method can provide not only collapse PGA of a low-rise RC building structure, but also damage conditions of members at a specific PGA. Combining with the deterioration rule for RC column after multiple earthquakes, it can also be applied to seismic analysis for after-earthquake or aged buildings.

最后则提出一套适用於中低层RC建筑结构之实用耐震诊断法，依照合理假设之地震力竖向分配型态及ATC-40建议公式，可再将层剪力-层间变位曲线换算为基底剪力-屋顶位移能力曲线，并计算对应之等效周期、阻尼比与PGA，除可评估结构整体之崩塌地表加速度外，也可由特定PGA反推对应的构件破坏程度，亦可配合震后折损修正，应用於结构之震后与经年耐震评估。

The paper introduces the basic principle about the new designing method of the external gear shaper cutter ,limited condition of the transformed cutter displacement factor,the formation of the limited ared and its relationship with the calculation curve of the cutter tip-circle's radius.

叙述了外插齿刀设计新方法的基本原理、转换后插齿刀变位系数选择的各限制条件、限制区域的形成及其与插齿刀齿顶圆半径计算曲线之间的关系，并通过实例介绍了其设计步骤。

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据。

To make the transition curve in the process of gear modeling be more reasonable, the parameterized 3D model of involute cylindrical spur gears with whole profile was made with Pro/Engineer software, based on the study of equations of the dual-arc rack cutter＇ s profile curves and the cut gear＇ s tooth profile curves.

为了使齿轮建模时过渡曲线部分更符合工程实际，在对双圆弧齿条型刀具轮廓曲线方程和齿轮的廊线方程研究的基础上，利用Pro/Engineer软件建立了可变位的渐开线完整齿廊直齿圆柱齿轮的三维参数化模型，并对齿廊曲线连续性进行了分析。

This paper put forward the method of calculating the number over teeth and pin diameter on the great addendum modification gear,and gave the number over teeth and pin diameter caIculation formulas easy to use in the work with curve fitting method.

文章提出了解决大变位齿轮跨齿数计算和量柱直径选取中存在问题的方法，给出了计算公式，用曲线拟会方法得出了便于使用的大变位齿轮跨齿数计算公式。

A feasible analysis of the higher scoring load capacity can be obtained from choosing the adequate correction factor, according to their opti- mization curves with increasing tool angle.

比较了所试各类齿轮的动力性能，从而为按优化曲线选择变位系数的齿轮或同时增大刀具角的齿轮具有更高的胶合承载能力提供了较充分的依据和可行性分析。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。