取出

Divide batter between pans and bake in middle of oven until a tester inserted in center comes out clean, 1 hour to 1 hour and 10 minutes.

将面团平均分到两只烤盘中，入烤箱烘烤，至测试器插入蛋糕中取出时无粘黏，这约需1小时或1小时10分钟。

In a manner worthy staff will book a good storage according to the order in a manner worthy of the book in a manner worthy tuhung, took out a placard with a commentary and electrographs in the samplecopy of the book is correct, check the time by the collar, Assistant, storage in a manner worthy staff third-party can only be found in order to determine the distribution page

2储帖人员将书帖依顺序储好在书帖斗后，各取出一帖配成册与样书核对是否正确，核对时由领机、助手、储帖人员三方确定无误方可进行配页

After removing the above stuff, check diaphragm and ○-ring is damaged; Do not be divided without damage to the internal parts on their own struggle.

如发现膜片或○型圈有损坏，请将轴芯上的螺帽松脱，逐浙分解出膜片或型圈，取出后重新换上新的膜片或○型圈。

He took a cigarette from the case.

他涨红了脸，从烟盒里取出一支香烟。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Please insert the key into the spindle-hole on the clock dial, tighten the spring full by clockwise way(but by anti-clockwise for head 3#), and take out the key.

请把钥匙插进钟面上的&条轴孔&（应插到底部，如图1所示）按顺时针方向上满发条，然后取出钥匙。

This time, we co-organize with PolyU Katso and the gathering was held in N113 room of PolyU from 7:30 to 9:15. We had around 23 people coming.

然后上主天主用那由人取来的肋骨，形成了一个女人，引她到人前，遂说：「这才真是我的亲骨肉，她应称为「女人，」因为是由男人取出的。

Dad took a pin and pinned the flower to his coat.

爸爸取出一枚别针，将花别在他的外衣上。

Bring the sugar and water to boil for 1 minutes then take 3 Tbsp. and mix with the rum. Beat chestnut puree, rum and icing sugar together. Whip the cream until stiff and slowly fold into the chestnut mixture , let aside .

把糖与水煮沸1分钟后，取出3汤匙与朗姆酒混合，将栗子茸、朗姆酒及糖霜搅匀，把打好的奶油加入栗子茸内，备用。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。