参考电平

Most people consider the return current when considering a fully differential circuit, but when considering the more usual circuit where a signal is referred to 'ground' it is common to assume that all the points on the circuit diagram where the ground symbol is to be found are at the same potential.

分析差分电路时，绝大多数工程师都会注意到返回电流，但对于常见的所谓单端电路，即所有信号采用相同参考点的电路，往往会认为电路中所有标有参考点符号的地方电平都相等。

The level at the reference point is zero.

参考点的电平是零。

Measure character: Frequency limits: CH1:dResolution of C ～ 225MHz frequency: 10 / second time-interval resolution : N/A measures speed: Can amount to 200 times measure / the second mixes in limits of the voltage on GPIB sensitivity : DC ～ 100MHz: 200MHz of ～ of 5Vac+dc 100MHz of 20mVrms ～±: 225MHz of ～ of 5Vac+dc 200MHz of 30mVrms ～±: Input of 5Vac+dc of 40mVrms ～± adjusts:(CH1 chooses) impedance, coupling: 1M Ω or 50 Ω, ac or Dc are low connect filter: 100kHz, but switch attenuation:× 1 or reference of × 10 exterior time base inputs: 1, 5, 10MHz sparks: CH1, to rising / drop the edge sparks, the percentage that uses signal n or absolutely voltage install n, setting sensitivity mixes to low, medium or tall gate start: Automatic, the hand is moved (setting gate time or resolution digit); Exterior, defer interface: Standard GP-IB(IEEE 488.1 and 488.2), take; of SCPI compatible language to say RS-232 power source only: 10 ％ of 100-120VAC ±, 50, 60 or 10 ％ of 400Hz ± 10 ％ of 220-240VAC ±, 50 or 10 ％ of 60Hz ± are suttle: 3kg dimension: 348.3mm of × of 212.6 × 88.5H

测量特征：频率规模：CH1：dc～225MHz 频率分辨率：10位/秒时候距离分辨率：N/A 测量速度：可达200次测量/秒在GPIB上电压规模和灵敏度： DC～100MHz： 20mVrms～±5Vac+dc 100MHz～200MHz：30mVrms～±5Vac+dc 200MHz～225MHz：40mVrms～±5Vac+dc 输入调节：(CH1选择)阻抗，耦合： 1MΩ或50Ω，ac或dc 低通滤波器： 100kHz，可切换衰减：×1或×10 外部时基参考输入： 1，5，10MHz 触发： CH1，对回升/回升沿触发，用信号电平的百分数或相对电压设置电平，设置灵敏度至低、中或高闸门和启动：主动，手动(设置闸门时候或分辨率位数)；外部，延迟接口：尺度GP-IB(IEEE 488.1和488.2)，带SCPI兼容说话；只讲RS-232 电源：100-120VAC±10％，50，60或400Hz±10％ 220-240VAC±10％，50或60Hz±10％净重：3kg 尺寸：212.6×88.5×348.3mm

In OverEasy mode, signals begin to gradually activate the 166XL's gain change circuitry as they approach the THRESHOLD reference level and they do not get fully processed in the manner defined by the RATIO control until they have passed somewhat above the THRESHOLD reference level.

在OVEREASY模式（OVEREASY按钮按下时），当输入信号逼近压缩阀值参考电平时，信号开始逐渐地被166XL增益改变电路激活，但它们不会完全地被压缩比所定义的方式去处理，直到他们已经稍微通过这个压缩阀参考电平。

Went up to undertake discussion to control of vector of asynchronous electric machinery and the interface between 3 n in this foundation, basically fall to vector place the synthesis of vector of fan area and judgement of small triangle area, referenced voltage undertook discussion, gave out to emulate a result.

并在此基础上对异步电机矢量控制和三电平之间的接口进行了讨论，主要对矢量所落扇区及小三角形区域判定、参考电压矢量的合成进行了讨论，并给出了仿真结果。

The number of nepers is the logarithm of the ratio of the measured power levels.

奈培数等于所测的电平功率与参考电平的比值取自然对数。1奈培等于8.686分贝。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失