参数表示

The method in computer clsed befone is the method of nodal line. The method is appropriate if the computing procedure is separate from CAD procedure. But if they are integrative the method isn't appropriate.

以前的桥梁混凝土构件电算办法是节线法，这在结构计算程序与CAD程序是分开来时是合适的，如果CAD程序与结构计算程序合为一体时，节线法就不合适了，因为CAD程序的几何元素是用参数表示的[1 ] 。

Based on the local parametric representation of a curve, the mathematical models of planar mechanism optimum synthesis for the local path generation are built. Objective functions are constructed generally and for some special cases as well.

在平面曲线局部参数表示的基础上建立平面机构局部轨迹优化综合的数学模型，构造了一般情况下及常见特殊情形的优化目标函数。

Properties of bi quadratic B spline surface are investigated by the subdivision approach, and the control mesh of bi quadratic B spline surface is constructed by employing Doo Sabin subdivision to derive the parametric representation of interpolation surface.

文中利用子分曲面理论研究双二次 B样条曲面的性质，在此基础上利用 Doo- Sabin子分模式构造插值顶点位置和法向的双二次 B样条曲面控制网格，得到插值曲面的参数表示。

This subcommand can be invoked from all execution modes but be careful when you use it from a ring-0 client (you will most likely crash your system if you just blindly break into winice and attempt to use this command).

控制你的光驱，没有参数表示停止播放CD，否则它从尝试播放一个指定的轨道。该子命令适用所有的执行模式，但当你从ring-0 client用它时要十分小心。

Experiments show that C-B spline curve, uniform B-spline with shape parameter, hyperbolic polynomial uniform B-spline with shape parameter and trigonometric polynomial uniform B-spline with shape parameter can be used to produce some frequently used free form curves in the industrial field when the shape parameter is assigned with some specific values. This process is simpler than producing these free form curves by using controlling vertex.

实验证明，C-B样条曲线、带形状参数的均匀B样条曲线、带形状参数双曲多项式的均匀B样条曲线、带形状参数三角多项式的均匀B样条曲线都可利用形状参数的特定取值表示一些工业领域常用的自由曲线，这比起用控制顶点表示同样的自由曲线更为简单。

Postural sway was measured by seven parameters derived from a force platform (kistler-9281). The seven parameters were: 1 CP sway area; 2 CP total excursion; 3 mean velocity of CP sway in the mediolateral and anterioposterior directions; 4 mean value of CP sway amplitude in the mediolateral and anterioposterior directions; 5 variability of CP sway amplitude in the mediolateral and anterioposterior directions; 6 mean value of the force signal in the mediolateral and anterioposterior directions; 7 variability of force signal in the mediolateral and anterioposterior directions; Repeated measures ANOVA procedures were used to analyze the effect of vision condition and ankle sprain.

身体摆动的大小以测力板量取的反作用力经过处理后的参数表示之，这包括，压力中心的摆动面积、压力中心的摆动轨跡长度、压力中心在两轴的平约摆动速度、压力中心在两轴的平均摆动幅度、压力中心在两轴的摆动幅度的变异性、反作用力在两轴的平均摆动幅度、反作用力在两轴摆动幅度的变异性。

In the case of floating-point input format this parameter is the number of the fixed float filter used for differencing .

当输入图像是浮点数格式时，该参数表示用来计算差分固定的浮点滤波器的个数。

These conditions are represented by the coefficients of the local systems and quite easily to be checked.

由于这些条件是用子系统的参数表示的，所以易于验证。

For the application of Mathematica in the differential geometry,this paper introduces how to processe the curve curvature and the torsion questions,the graphic expression of the curvature and the torsions,and draw curves by the curvature and the torsions. Curvature ; torsion ; solution curve ; osculating plane ; natural parameter ; natural equation

利用Mathematica，只要输入有关系统命令就可以得到期望的结果。1曲率和挠率及其图形意义假设R3上的曲线一般参数表示为r=r它的曲率和挠率计算公式是：κ=‖r′×r&‖‖r′‖3τ=‖r′×r‖我们知道，空间曲线r=r在一点(s=s0)邻近的近似方程为ξ=sη=120κs2ζ=160κ0τs3通过近似方程可以确定曲线在其基本三棱形的三个平面(即密切平面，法平面，从切平面)上的投

The hot helium temperature follows HTR-10's nuclear power changes slowly, and there is a large coupling between them, so the RPHHT system adopts cascade control, the minor loop is fast, and the major loop is hot helium temperature control loop whose dynamic response is slow; there is also a large coupling between main helium loop and steam-water loop, and both the main steam temperature measure signal and the heating process of the once-through steam generator are delayed, therefore, the MHFMST applies cascade control, the minor is main helium flow control loop whose dynamic response is fast, and the major is the main steam temperature control loop whose dynamic response is slow.

本文运用机理建模法，建立了HTR-10系统动态控制模型，然后进行了动态性能仿真，将堆芯用集中参数表示，冷却剂按一维流动处理；直流蒸汽发生器按二回路工质不同的相分为预热段、蒸发段和过热段，建立了三环节控制模型，得到HTR-10系统控制模型；仿真结果与数值计算结果对比表明，本文所建立的控制模型，能近似地反映HTR-10的动态特性，适合设计控制系统。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。