参数的

By using the group-chain, the wavefunctions of the 4f〓 configuration for RE ions are also expressed as linear combinations of group-chain basis functions in Butler's irreducible representation notation. The matrix elements of the CF Hamiltonian then are calculated by means of the Wigner-Eckart theorem and factorization lemma of the jm factors. Before the CF level fitting, a point-charge calculation of the conventional CF parameters B〓 has been performed by means of the lattice-sum technique from the known crystal structure data. The corresponding parameters in the group-chain are calculated by the conversion relationship between two schemes that proved identical in essence, which are usually used as initial values in the fit to the experimental levels. The ratios of the same k-value CF parameters are suggested as the constraint conditions in the fit, in order to utilize fully the symmetry distortion degree of the studied system.

利用群链理论，属稀土离子4f〓组态的波函数表示为以不可约表示标记的群链基波函数的线性组合；借助Wigner-Eckart定理和2jm和3jm因子的分解定律计算了晶场哈密顿的矩阵元；根据点电荷模型和已知晶体结构数据，利用点阵求和技术计算得到传统晶场参数B〓初值，相应的非传统形式的群链参数初值则由两种方案下的转换关系求得；这些初值通常作为非线性拟合晶场能级计算的初值，系统的对称性畸变信息则反映在以同阶晶场参数的比值作为能级拟合的约束条件。

In order to improve the reliability of the nuclear Generating Sets and the stabilization of the power system, prevent the long time low frequency oscillation caused by the disturbed of the outside electrical net, assured improving the stabilization margin of the nuclear generating sets in the precondition of enough transient stability, validate the sensitivity of the parameter to the damping of Generating Sets of the MEC5220 digital excitation adjustor produce in Japan that used in the Second Project of Qinshan Nuclear Power Plant, confirm the parameter rationality of the digital excitation adjustor, optimize the parameter of PSS, in this paper, we put up a in-depth study to the principle of MEC5220 digital adjustor produce in Japan by the PSS/E software that develop by the PTI Company in the USA, completed the modeling of the excitation adjustor, PSS, generator, excitor, described the performance of this excitation adjustor, analyzed the essential reason that caused the low frequency oscillation, illuminated the factor that influence the damping characteristic of the MEC5220 digital excitation adjustor. Based on model and emulate, this paper optimized the primary parameter of the excitation adjustor, make a reasonable regulation to the PSS parameter.

为提高核电机组的运行可靠性和接入系统的安全稳定性，防止在外电网的干扰下核电机组发生长时间的低频振荡，保证机组在暂态稳定的前提下提高其稳定裕度，验证秦山核电二期核电机组所配日产MEC5220型数字式励磁调节器参数对机组阻尼的灵敏性，确定数字式励磁调节器的参数的合理性，优化PSS整定参数，本文利用美国PTI公司研发的PSS／E软件对日产MEC5220型数字调节器的原理进行进行了深入细化的研究，完成了励磁调节器、PSS、发电机、励磁机的建模，描述了该型励磁调节器的性能，分析了产生低频振荡的根本原因，阐明了影响阻尼特性的因素。

In this article two functional modes of the Fly-back Converter (Continuous Conduct Mode and Discontinuous Conduct Mode) are particularly analyzed, which include their characteristics, applications, the critical pattern of two functional modes is argued, both the exact boundary from the angle of circuit parameters is crystallized, at the same time, basic principle of PFC under the DCM mode is introduced, which settle theoretical basis for the subsequent design; by establishing the mathematic model of the converter, a further investigation of the configuration is made, qualitatively and quantitatively, analyzed to settle exactly theoretical basis for the subsequent emulation and the experimental parameter; from the angle of steady-state analysis, the transfer function of the system is deduced to establish dynamic small-signal state equation, emulating the system with the help of matlab, then according to the simulation result and the theory of PFC revise the system, lastly, we adopt the project which add a zero-pole compensator to the voltage loop, by this way, a satisfied system performance is gained and the PFC scheme is ensured successfully; finally, based on the previously-done work, we combining with the situation of specific design requirement, acquired the numerical value of each unit devices in this converter

详细分析了反激式变换器的两种工作状态，连续模式(Continuous Conduct Mode ，简称CCM)和断续模式(Discontinuous Conduct Mode，简称DCM)以及各自的特点、应用场合，论证了两种工作状态的临界模式，从电路参数的角度明确了二者的界限，同时还介绍了DCM模式下PFC的基本原理，为后面的设计奠定理论基础；通过对整个变换器系统建立准确的数学模型，对此变换器的电路结构做了进一步的研究，定性、定量地分析了变换器各部分的工作状态，为仿真和实验参数的确定以及电路参数的优化提供理论依据；从稳态分析的角度，为系统建立了动态小信号状态方程并推导出系统的传递函数，利用matlab对系统进行仿真，进而根据仿真结果以及PFC的相关理论对系统进行校正，采用在电压环加入零点—极点补偿器的设计方案，得到了满意的系统特性并且保证了PFC的顺利实现；最后，在前面所做工作的基础上，结合设计要求计算出此变换器系统中每个元器件的数值，利用Pspice对其进行了仿真、优化，然后根据仿真结果搭建了硬件电路。

ABSTRACT Aiming at problems of trans-vector controller in a vehicle-carried induction motor such as variable rotor and stator resistance following motor temperature, and their inductance varying with flux saturation degrees. Firstly, CSI and VSI are introduced, for CSI, it can hold the advantages both FOC and DTC using stator flux directional, PI parameter and simulation are also introduced. Secondly, equations of IM in the synchronous rotary frame and its static counterpart, as figuring in the saturation condition of magnetic field, are dealt in this paper and the simulation results are presented. Thereafter, the parameter designing of PI trans-vector controller is processed, which features the non-linear model. In practical realization, as neglecting the dynamical change of motor inductance, this paper employs online modification of inductance parameters, according to the flux saturation, then transforms the non-linear equations into linear ones, and so compacts the structure of controller. Thirdly, in view of the maximum torque output is extraordinary requisite when Electrical Vehicle start up, accelerate, and overtake, this paper issues the maximum torque when both inverter and battery capacity is corporeally definite. Fourthly, on-line differentiating and analyzing both rotor's time constants and its flux by using the expanding order reduction and discrete Kalman filter equation are fathomed, in order to realize high-performance trans-vector algorithm, and also the simulation results are presented. Fifthly, the close-loop regenerative brake system, when the EV's torque is set constant, is deduced; at the same time, unification of electric drive model and brake model is executed. Combined with maximum charge current demands, the mathematical model for online yielding torque as a demand.

本论文针对车载异步电机在矢量控制器所遇到的问题：定转子电阻随温度变化及随电机饱和程度变化的转子电感及定子电感而影响电机调速性能提出一套完整的解决方案：分析了电流型逆变器和电压型逆变器在实现矢量控制时控制器参数的计算，分析出对于电流型逆变器在采用定子磁场定向时，其性能同时具有矢量控制和直接转矩控制两者的优势，并对电压型逆变器在转子磁场定向下的模型进行了仿真研究；建立异步电机非线性模型，推导出考虑磁饱和时异步电机在同步旋转坐标系及静止坐标系下的方程，并做出了仿真结果，建立异步电机在非线性模型下的矢量控制调节器的PI参数设计，在实际应用中，若忽略电机电感的动态变化，可以根据当前的磁路饱和状态而在线修正电感参数，从而将非线性方程线性化，降低控制器的复杂度；考虑到电动汽车在起动和加速超车时需要电机有最大转矩输出，本文讨论在逆变器容量一定和电池供电能力有限的情况下电机最大转矩输出问题；推导了异步电机扩展降阶、离散卡尔曼滤波方程在线辨识转子时间常数和转子磁通，用于实现高性能的矢量控制算法，并给出了仿真结果；推导出了电动汽车恒转矩给定的闭环回馈制动系统，实现了电动控制模型和制动模型的统一，而且结合铅酸电池最大充电电流的要求，为制动转矩在线给定建立了数学模型；设计了基于双DSP系统的高性能矢量控制器软硬件框图，并以大量实验数据说明矢量控制在电动汽车应用的实际应用状况。

In order to reduce calculation error, the frequency distribution of average values is used to compute the mixed distribution's digital features of each component distribution, thereinto, the number of the component distribution is determined by AIC, choose the number that meets the minimum value of AIC as the component number of mixed distribution, and the other parameters are estimated by EM algorithm; Secondly, because each component distribution is corresponding to a kind of major gene genotype, according to the values of the average and variance of the each component distribution, we can use the limit error of the normal distribution to plot each individual into the correspondent component distribution, namely into correspondent major gene genotype. Then we regard each major gene genotype as a treatment level of one-way analysis of variances, and the one-way multivariate analysis of variance is carried out to calculate the covariance matrix of major gene effect, covariance matrix of polygene effect, covariance matrix of environment effect and so on; At last, combining the weights of the each component distribution of mixed distribution, we can calculate the variance of major gene effect, the variance of polygene effect, environmental variance and the genetic gain of the quantitative trait.

为减小计算误差，本研究采用均值的频数分布来计算各成分分布的数字特征，其中成分分布个数根据AIC准则，选择使AIC值达到最小的成分分布个数作为混合分布的成分分布数，分布中其它参数的确定利用EM算法来估计；其次，每个成分分布对应一种主基因基因型，根据各个成分分布的均值和方差，利用正态分布的极限误差将每个个体划分到相应的成分分布中，即相应的主基因基因型中，将每种主基因型作为单因素方差分析的一个处理水平，对其进行单因素的多元方差分析，分别计算主基因效应协方差阵、多基因效应协方差阵、环境协方差阵等参数；最后结合混合分布中各成分分布的权重即各主基因基因型的分离比例，计算主基因效应方差，多基因效应方差和环境方差，以及遗传力等参数，进而计算该数量性状的遗传进展。

By setting up the mathematical models of the regulating objects （combusting heat transfer, heat utilization and storage, superheater and main steam pipe line）, by combining heat transfer function of regulating system and by selecting method of setting PID accoding to set attenuation index object, the corrections among PID and pulverized coal＇s caloric values are found. Now the PID can be set according to caloric values of the pulverized coal burned in the unit and the automatic control can be put into operation.

通过建立调节对象四个环节（燃烧传热过程、热量的利用和储存过程、过热器、主蒸汽管道）的数学模型，结合调节系统的传递函数，选用按给定衰减指数设定PID参数的方法，找出PID参数与煤粉热值的关系式，最终达到在机组燃烧不同热值的煤粉时可依据该方法设定不同的PID参数、并都能投自动的目的，从而有利于提高机组的稳定性，并可节约煤粉。

Such parameters as the percentage of ordinary reinforcment, amounts and configuration of unbonded prestressed tendons, the ratio of span to depth and the loading patterns were considered. Based on the results, the fomula for the eqivalent length of deformation zone on the beams at ultimate were developed. A simple formula was developed for the ultimate mid-span deflection of concrete beams with concept of equivalent length of deformation zone, and the deformation of beam before internal reinforcement yielding was predicted by the traditional formula for the deformation of partically prestressed concrete beam. Then an analytical model was deduced for analyzing the ultimate stress increment in those concrete beams prestressed with external or internal unbonded tendons based on the mid-span deflection.(4) Testes were carried out on a thin-walled concrete box beam presressed with external CFRP tendons to study its short-term performances under uniform load, long-term behaviors under uniform load, and full-time performance under four-point load in turn.

3以体内非预应力钢筋配筋率、体外预应力筋配筋率、体外预应力筋布置形式、预应力度、跨高比、荷载形式等为参数，用非线性分析程序对体预应力筋混凝土梁进行了参数分析，依据分析结果提出了以综合配筋指标和预应力度为参数的等效变形区长度的计算公式，进而提出了基于等效变形区长度的极限挠度计算公式；体内非预应力钢筋屈服前的挠度计算采用常用的部分预应力混凝土梁挠度计算公式；依据试验和非线性数值计算结果，将不同转向块布置形式的体外预应力混凝土梁简化为跨中一个转向块的体外预应力混凝土梁，推导了基于跨中挠度的体外预应力筋应力增量的简化计算公式。

Such parameters as the percentage of ordinary reinforcment, amounts and configuration of unbonded prestressed tendons, the ratio of span to depth and the loading patterns were considered. Based on the results, the fomula for the eqivalent length of deformation zone on the beams at ultimate were developed. A simple formula was developed for the ultimate mid-span deflection of concrete beams with concept of equivalent length of deformation zone, and the deformation of beam before internal reinforcement yielding was predicted by the traditional formula for the deformation of partically prestressed concrete beam. Then an analytical model was deduced for analyzing the ultimate stress increment in those concrete beams prestressed with external or internal unbonded tendons based on the mid-span deflection.(4) Testes were carried out on a thin-walled concrete box beam presressed with external CFRP tendons to study its short-term performances under uniform load, long-term behaviors under uniform load, and full-time performance under four-point load in turn.

3以体内非预应力钢筋配筋率、体外预应力筋配筋率、体外预应力筋布置形式、预应力度、跨高比、荷载形式等为参数，用非线性分析程序对体预应力筋混凝土梁进行了参数分析，依据分析结果提出了以综合配筋指标和预应力度为参数的等活动房效变形区长度的计算公式，进而提出了基于等效变形区长度的极限挠度计算公式；体内非预应力钢筋屈服前的挠度计算采用常用的部分预应力混凝土梁挠度计算公式；依据试验和非线性数值计算结果，将不同转向块布置形式的体外预应力混凝土梁简化为跨中一个转向块的体外预应力混凝土梁，推导了基于跨中挠度的体外预应力筋应力增量的简化计算公式。

With proper equations of state the relationship between the pressure and the isothermal bulk modulus is presented, which is compared with those data that come from PREM and PEM values. In order to know more about the property of matter in the inner earth's core we presented the relationship between the temperature and the volume, and the relationship between the temperature and the thermal pressure.

采用与现有地震学数据一致的地核物质状态方程，计算了300K时压强-不可压缩系数的关系图，并与地核环境下PREM、PEM模型的数据加以比较；给出了内地核环境下温度-摩尔体积、温度-热压等参数的关系曲线，研究了地核物质的热学参数；应用计算所得到的热压值，借助量子统计物理的方法，列表给出了与内地核物质量子效应有关的各项参数。

In order to make these silver paste successfully used in commercial, a clear understanding is required for the complex relation between different parameters such as particles size, solid volume fraction, packing density on suspension printing and deformation and the mechanism of silver powder sintering shrinkage and the inorganic adhesive effect under the batch manufacture condition.The main emphasis of our researches was to improve the silver paste properties by developing a reliable, screen-printing paste suitable for fine lines and lower sintering porosity and good interface between thick film and glass substrate.

为开发电学性能稳定、高导电率、具有良好细线印刷性能及优良附着性的高性能电子浆料，本研究着眼于对影响参数进行详细剖析，找到关键控制参数，通过研究微观结构与粉末参数的对应关系，找到如何能制备出具有致密的厚膜结构与较低的孔隙率，并且其浆体与有机载体的界面区也要有明显的改善的电子浆体；同时对批量生产的银粉的形态与粉末烧结反应的收缩现象，无铅玻璃体系对银膜致密化等过程进行研究，获得致密高导的无铅银浆料。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。