参数的

Dynamic and static elastic parameter s of rock samples are measured synchronistically under triaxial stresses.

在三轴应力下对砂、泥岩等岩芯进行了岩石力学参数的动、静态同步测试，并对动静态弹性参数进行了线性回归。

The relation of the volumetric ratio ,reflectivity and transmissivity can be deduced by the conservation law of energy.

建立该复合材料热物性参数与纤维和基体热物性参数的关系理论模型。

Loop-control parameters shall be available inside the do-loop for words that use or change these parameters, words such as I , J , LEAVE and UNLOOP .

回圈控制参数必须在 do-loop 中可被用来改变这些参数的词存取，像是 I ， J ， LEAVE 和 UNLOOP 。

The relationship between the structures and properties of these compounds was discussed.

讨论了各性能参数与其结构参数的关系。

Cutting parameters are filtrated, range of cutting parameters is reduced based on criterion of bending stress flexibility distortion.

依据弯曲应力和挠度变形判定标准，进一步筛选切削参数，缩小试验参数的范围。

Considering the inconvenience of regulation and difficulty of parameter tunning as AC servo system in practical situation, three ways of intelligent control approach to realize auto-tuning and autorecognization of AC servo system, are proposed, which is a robust controller based on two-degrees-offreedom with no tuning to controller, a auto-tuning controller based on fuzzy reasoning with no inertia recognization but tuning parameter of controller, a strategy recognizing inertia of servo system and tuning parameter or structure of controller automatically. In the same time, these control strategies are analyzed from the theory and reliability. The comparative analysis of three measures on strong and weak points is made by simulation and experiment results.

针对交流伺服系统在实际应用中存在的系统调试不便、参数调整困难等问题，提出了实现交流伺服系统自调整和自识别等智能化控制策略的三条途径：一是具有控制器无调整特点的二自由度鲁棒性控制器；二是惯量无识别但需自动调整控制器参数的模糊推理自调整控制器，三是自动识别伺服系统转动惯量并自动调整控制器参数和结构的方案，从理论分析和可实现性两方面对这些控制方案进行了论述，并通过仿真和实验研究，对比分析了各种方案的优缺点，得到了一些有益的结果。

According to the geological property of the research area, we apply sequence indicator simulation method if the reservoir type is discrete variable. Sequence Gauss simulation method is used if the type of reservoir property is continuous variable. Structural model (single well model, fault model and bedding model) and property model are built. The 3D distributions of reservoir parameters are established based on structural model. Three advantage oil distribution of the oil field are pointed out through overlap of the reservoir parameters distributions.

根据研究区的地质特征，建模过程中的储层类型属于离散变量，选用序贯指示模拟方法；储层参数属于连续变量，则选用序贯高斯模拟方法，对储层分别实现构造建模(单井模型、断层模型和层面模型)和属性建模，在构造模型的基础上建立储层参数的三维分布，通过储层参数的分布的叠合研究，在该油田指明了三个有利油气分布区块

Based on the theory study, a directional drilling guidance system is developed for practical require, its working flow as follows: before construction, design the best track practically, and save in the system. During drilling, the system measures well oblique angle and azimuth to watch well track. Drill driver compares designing well track with measuring track showing on display unit, controls joy stick experientially, adjusts drill direction, finally realizes directional drill.

在理论研究的基础上，结合实际需要，研究设计了一种定向钻井导航系统，使用该系统进行定向穿越施工的工作过程如下：在施工前，根据实际情况，先设计一条最佳穿越路线，存入系统；在钻进中，系统通过对井轨的井斜、方位等参数的测量，对其进行实时监测；地面的司钻手通过对显示仪所显示的实际井轨参数及设计井轨参数进行比较，根据经验操纵操作杆，调整钻机前进方向，以达到对钻进过程的控制，最终实现定向钻井。

Adhibiting the nerve cell and qurdratic capability target, by the self-adapting self-studying consistent and better abiding of the nerve cell ,the thesis realizes the conforming of the parameter not depending the canal mathematics ,furthermore the parameter can self-adjust for the information of the canal.Combining the BP nets and the routine PID controller, and adhibiting the linear optimization target function, the thesis realizes the conforming of the parameter not depending the canal mathematics, furthermore the parameter can self-adjust for the information of the canal. Using the MATLAB the thesis simulates and acquires some significative effects.

在传统PID渠道控制中引入了神经元和二次型性能指标，利用神经元自适应、自学习、并行处理及较强的容错能力，实现了PID控制中参数的整定不依赖于渠道数学模型，且PID参数能根据渠道的适时信息在线调整以满足适时控制的要求将BP网络与常规PID控制结合，并引入了最优化目标函数，利用BP网络来实现PID控制器参数的在线整定，将其运用于渠系等体积控制，并利用MATLAB软件进行了数值模拟仿真，取得了一些有意义的成果和较为满意的结果。

The truth of the measuring method is established by precision and feasibility analysis.The restriction of using this method to measure surfaces of roller gear cam is discussed, and the next research direction is confirmed.

分析了这种弧面分度凸轮测量方法的局限性，即该方法只适于对已知参数的弧面分度凸轮进行精度检验；如果要测量参数未知的凸轮，反求参数，这种方法是不适用的；针对该方法的局限性确定了下一步的研究方向。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。