参数的

The result shows that the specific thrust performance of ITB engine is better;the specific f uel consumption curve is toning down with the varied cycle parameters mentioned above, the range which cycle parameters can b e selected is wider than that of conventional engine.

结果表明：这些循环参数变化时，涡轮级间燃烧室发动机单位推力增长幅度较大，耗油率性能变化曲线趋于平缓，发动机综合性能提升，循环参数的可供选择范围变宽。

JS11 Intelligent Straight-line Beveling Machine and a PG10 glass polishing machine, Its Joint-Link adopts chainless ball bearing construction .smooth transmission, high-precision movement , The controlling system adopts PLC, which can be operated manually or automatically. The human-machine interface displays various parameters, such as the glass thickness, bevel width and angel, remaining thickness, and working speed The convey speed adopts speed adjustment of frequency conversion The machine can grind and clean the rear transmitting plate of itself.

JS11玻璃直线斜边磨边机及PG10璃直线斜边抛光机采用无链条轴承滚动链板结构，传动平稳，运动精度高，控制系统采用PLC控制，可自动、手动转换，人机界面清楚显示玻璃厚度、斜边宽度及角度、剩余玻璃厚度和加工速度等各种参数，参数的输入和修改直观、便捷，自动化程度高，传送速度采用变频调速，能在本机上进行修磨后板，并设有后板自动清洗装置。

A motion parameter estimation method by fitting the phase history of the moving target is proposed for airborne dualchannel SAR systems. The crosstrack velocity, alongtrack velocity, crosstrack acceleration and alongtrack acceleration can be estimated, respectively.

针对机载双通道合成孔径雷达(synthetic aperture radar， SAR)系统中运动目标参数估计，提出了一种利用目标相位历程拟合目标运动参数的方法，包括距离向速度、方位向速度、距离向加速度和方位向加速度估计。

Results The influence factors on parameter of blood rheology were a long-term and excessive smoking; high triglyceride; excessive drinking; hypertension; hyperadiposis; hypercholesterol...

结果 影响血流变参数的危险因素依次是：长期大量吸烟，高甘油三脂，大量饮酒，高血压，过度肥胖，高胆固醇。结论具有心脑血管病危险因素者血液流变学参数与正常人相比明显异常。

The determination of parameters σ and p is converted into the definition of an inequal upper boundary from solving integer programming problem, which decreases the calculation of solving parameters so that the application of CF-PCG algorithm in pactice is more convenient.

分析了CF－PCG算法的效率随其参数的变化性质，将参数σ，p的确定，由求解整数规划子问题转化为确定一个不等的上界，从而减少求解参数的计算量，使CF－PCG算法的实现更加方便。

By proximate and ultimate analysis, petrographical analysis, Scanning Electronic Microscope analysis, Mercury Porosimeter analysis, TG analysis and pilot scale fluidized bed combustion experiment, the combustion characteristics and particle properties of Longyan coal with different lithotype were studied, including the surface figure and pore structure of particle, the maceral content, the ignition and burnout temperature, and the reactivity, ect.

利用热天平实验测试数据，分别采用Freeman-Carroll微分法、改良Coats-Redfern积分法和Flynn-Wall-Ozawa法等热分析手段求解4种无烟煤的燃烧动力学参数。研究不同热天平试验工况、不同处理方法和不同拟合区间等对求解结果的影响，分析用不同热分析方法求解反应动力学参数的可靠性并计算得到了几种典型福建无烟煤的燃烧反应动力学参数；再次是研究流化床燃烧中无烟煤焦的反应性随燃尽度的变化。

The above results showed that physiological AAI pacing maintained a normal EAS and VAS, and improved or enhanced VSS; while nonphysiological VVI pacing and physiological DDD pacing induced the decrease in VSS due to an abnormal EAS and VAS. Furthermore, with increasing the pacing rate, VSS was markedly decreased.The quantitative comparison of parameters of left ventricular systolic function obtained by computerized ERNA showed that AAI pacing induced the significant increases in ventricular ejection rate and stroke volume with concomitant shortening of ejection time.

应用计算机-ERNA相位分析技术，对13例生理性AAI、13例非生理性VVI及6例生理性DDD患者，分别进行等相位电影，相位图，相位直方图和VSS参数的静动态观察和定量比较，结果显示：AAI起搏可维持正常EAS和VAS，心室相位均匀一致，并且VSS参数-相角程，半高宽和峰相位标准差均较起搏前分别降低，提示起搏后VSS有所改善或增强。

From the viewpoint of controlling the processing parameters, the production technology of fine denier polypropylene POY is explorated . The effects of the parameters on the structure and properties of the POY are analysed, thus the optimal processing condition is found.

本文主要从分析工艺条件及参数的控制出发，对细旦丙纶POY的生产技术进行探讨，了解这些参数对POY的结构和性能的影响，从而为寻求最佳化的工艺参数指明方向，以求正确指导细旦丙纶POY的生产。

And nonlinear least square method was used to fit the rhe...

并运用非线性最小二乘法，对水泥浆流变参数随时间变化曲线进行了拟合，得出流变参数的计算公式。

After that , simulated the Die Casting filling process of liquid metal .First use the spical soft Pro/E to construct the model of Die Casting part; Input it to another soft I-deas to form mesh and put the mesh document to the special soft ProCAST.

接着模拟了金属液在模具型腔的充填过程：运用Pro/E软件对泵盖进行三维实体造型，然后把图形导入软件I-deas中进行网格化处理，并将网格化后的模型输入到ProCAST软件中进行了关于压铸工艺参数的多组正交试验的流场，温度场的偶合模拟，进而从多组试验参数中找出最优的压铸工艺参数。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。