参数曲线

Using VB6.0 to find practical briachial-bridge luffing mechanism and curve slideway live control weight gravity balance system rules and method.

运用这个软件进行参数化设计，从而找出一种实用的臂桥架变幅系统和曲线滑道活对重自重平衡系统设计准则与方法。

To investigate the pitting and metastable pitting rules of type 304 stainless steel, potentiodynamic polarization method was employed to study the behavior of metastable pitting and stable pitting on 304 stainless steel in sodium bromide solution and borate/phosphate buffered bromide solutions. The influence of the concentration of Br-、the pH value、the buffer capacity and general environmental factor to pitting potential and metastable pitting was studied as well.

为了更深入地了解304不锈钢的稳态及亚稳态孔蚀规律，本文采用动电位慢扫描法测得了304不锈钢的阳极极化曲线，研究了不锈钢在纯溴化钠溶液及含溴化钠的硼酸盐或磷酸盐缓冲溶液中的亚稳态孔蚀以及稳态孔蚀行为，分析了溴离子浓度、pH值、缓蚀性阴离子、以及缓冲容量和综合环境因子对孔蚀电位以及亚稳态孔蚀特征参数中的形核数目、峰值电流、生长寿命的影响。

The method for determination of sorbicacid ,sourcess of uncertainty of measurement such as concentration of standard solution,parameters of standard curve,and soy sample dilution were analysed.

按照GB/T5009.29-2003中山梨酸含量测定方法，对测量结果的不确定度来源如标准溶液浓度、校准曲线参数、样品稀释等进行了分析，对各不确定度分量进行了评定和量化。

The characteristics of cutting edge and cutting advantages for a new type of ball end mill with space curve cutting edge is introduced,the calculating method of curve geometric parameters is explained,and the manufacture technology is presented.

介绍了一种新型空间曲线刃球头铣刀的刃形特征和切削优点，详细分析了其空间几何参数的计算方法，简要说明了其制造工艺。

In the course of FEM model building, tensile test experiment is taken to work out the real stress-strain curve. Ring compress test is also done in this paper, through which the friction coefficient is worked out and the friction mechanism and relevant friction model for tube stagger spinning is studied. The experiments ensured the veracity and reliability of the FEM modeling.

建模过程中，通过材料拉伸试验测定了旋压材料00Ni12Cr5Mo4TiAlV时效钢的真实应力应变曲线；利用圆环镦粗试验测定了材料在不同润滑状态下的摩擦系数，并对强力旋压的摩擦性质和摩擦模型的选择进行了研究，确保了建模关键参数的准确性和可靠性。

In this paper, based on nonlinear FEA software ANSYS/LS-DYNA, 3D dynamic simulation models of eighteen-type tubes for backward spinning was established. This paper not only obtained spinning force of tube backward spinning but also obtained the spinning force curves varying with the different reducer ratio, feeds, fillet radius for spinning roller, forming angle and diameter of spinning roller, and diameter blank inner.

以大型非线性有限元软件ANSYS/LS-DYNA为分析平台，通过对18种几何尺寸和参数不同的筒形件三旋轮强力反旋旋压过程的三维动态模拟，得到了它们的旋压力以及旋压力随不同减薄率，旋轮进给量，旋轮圆角半径，旋轮成形角，旋轮直径和毛坯内径的变化曲线。

Using VB drawing three parameters spline interpolation curve, very good looking, easy!

采用VB绘制三次参数样条插值曲线，非常好看，方便！

Using VB drawing three parameters spline interpolation curve, very good loo...

采用VB绘制三次参数样条插值曲线，非常好看，方便！

A method of generating cubic spline curves with local shape parameters is presented in this paper.

给出了带局部形状参数的三次样条曲线生成方法。

You would also need knowledge of the following parametric equations for the Bezier spline.

你也将需要下面的贝塞尔曲线的参数方程的知识。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。