参数曲线

The advice on selecting weight function and its parameter in MLS method is presented by analyzing the influence of weight function curve on the precision of computational result on the basis of energy norm proposed.

通过建立误差的能量范数，对照分析了权函数曲线的分布规律对逼近结果的精度影响，得到了在移动最小二乘法逼近中选择权函数及其相关参数的建议。

Calculation of teeth profile of disc cutter for arc-gear;2. The formulas for setting angle and entrance angle of disc cutter s are derived by using the contact condition of space curve.

利用空间曲线相切条件导出了用于计算盘形刀具安装角和切入角的条件；该方法具有以下优点：无需知道工件齿形，可同时获得刀具宽度、半径等参数。

The relative carves between saving test time, relative error of the parameter estimation and terminating number are given.

给出了平均节省试验时间及参数估计相对偏差与截尾数之间的关系曲线。

Chapter Four deals with the linear admissible minimax estimators of linear estimable function of parameter matrix in the given linear estimator for a general growth curve model.

第四章讨论了一般增长曲线模型参数阵的线性可估函数在给定的线性估计类中的容许Minimax估计，并给出了具体的表达式。

In this paper, some researches on estimator of parameters in the growth curve model are considered.

本文主要研究了生长曲线模型中回归系数的参数估计问题。

With experimental datum, the models parameters are optimized with Levenberg-Marquardt algorithm, and for the best fitting curve of Fabry-Perot etalon transmittance.

根据实验测量数据，利用Levenberg-Marquardt算法对理论模型进行参数优化估值，获得测量数据的最佳拟合曲线。

The results show that in comparison with the exponential curve model and the GM (1, 1) model, the DE-GM (1, 1) model fits the measured data better and make s prediction more accurately. Furthermore, the DE algorithm is a highly effective algorithm with good properties such as high efficiency, high precision, fast computing speed and universality, etc.

结果表明，与指数曲线模型和GM(1， 1)模型相比，DE-GM(1， 1)模型能够更好地拟合实测数据，预测精度进一步提高；微分进化算法在GM(1， 1)模型参数优化过程中表现出求解速度快、计算精度和自动化程度高等特点。

In view of trust region algorithm has good global convergence for solving non-linear quadratic programming problem,the effective elastic module s damage factor and the damage distribution function is introduced by FEM updating .

鉴于信赖域算法在求解非线性二次规划问题中具有良好的全局收敛特性，同时结合有限元模型修正技术，引入有效弹性模量损伤因子和损伤分布函数的概念，在Matlab编程环境下调用ANSYS有限元程序中的APDL语言进行桥梁空间结构的有限元建模，利用信赖域算法调整局部单元的参数，通过连续损伤分布插值多项式拟合连续区段各单元的损伤分布曲线，进而实现了对连续梁桥的动力损伤识别。

Based on this property, by solving a series ODEs we construct a two-parametric family of helicoidal surfaces under cubic screw motion with prescribed mean curvature or Gauss curvature and solve an open problem left by Beneki.

基于这一点，当螺旋面的平均曲率或Gauss曲率为给定光滑函数时，本文选取伪正交标架，使得两类螺旋面的平均曲率和Gauss曲率的表达式相对简化，通过求解一系列的非线性常微分方程，即可确定一族生成曲线，从而最终确定平均血率或Gauss曲率为给定光滑函数的双参数族螺旋面，并在这一过程中解决了Beneki等人留下的一个公开问题。

Based on the comparison of the delayed neutron counter rate of known fission rate with the delayed neutron counter rate of a burst,a method to determine burst total fission number of burst reactor was built.

用长计数器测量已知裂变率的缓发中子计数率，然后用同一探测系统测量脉冲后的缓发中子计数率，探测系统的探测效率、缓发中子份额和缓发中子先驱核半衰期等参数均不变，从而建立起利用脉冲堆脉冲后的缓发中子衰减曲线确定脉冲裂变总数的方法。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新