参数曲线

The structure feature of the sensor was described in comparison with the classical Stewart platform-based six-component force sensor.By using the finite element method,the elastic dynamics theoretical model of the sensor was established based on the conditions of displacement consistency and force balance.According to this model,the numerical analysis was carried out,and the variety relationship curves between the natural frequencies and the structural parameters are plotted.

描述了该传感器相对于经典Stewart平台六维力传感器所具有的结构特点；利用有限元法，采用位移协调和力平衡条件建立了传感器弹性动力学理论模型，依此模型进行数值分析，绘制了固有频率与各结构参数间变化关系曲线；并利用ANSYS软件建立了传感器有限元模型，进行了振动模态分析，得到其固有频率和振型。

But parameters are appropriate or not, it must rest on constringency of solutions, quality of solutions, and many experiments.

在用遗传算法拟合曲线时，衡量参数设置恰当与否，要依据多次运行的收敛情况和解的质量来判断。

This paper first demonstrates that the changes of air parameters is indicated as a curve convex to the right in the psyehrometrie chart when the air flo ws through the surface air cooler in the cooling process.

本文首先论证了空气在表冷器中冷却过程的参数变化，在I——d图上表示的是一条向右凸的曲线。

The thesis presents the system parameter configuration,the dynamic curve and the coordinate orientation of metal position.

文中给出了调试后的系统参数配置，绘制的动态曲线以及金属位置的坐标定位图。

The longitude curve and the latitude curve are the coordinate curve in the new geodetic coordinate system with length as coordinate parameter.

本论文中引入一种新型的大地坐标系，这种坐标系是以经纬线为坐标曲线，以长度量为坐标参数的新型坐标系。

Middle spiral curve ; coordinate formula ; like parameter

中插缓和曲线；坐标公式；连接参数

The maximal depth model for single-pass milling process, the depth and surface roughness for plane surface are established. The milled profile of a single-pass milling of the jet can be modeled as a cosine curve of the form. Therefore, the maximal depth model for single-pass milling is established which indicates the quantitative relationship between the AWJ single-pass milling depth and the milling parameters.

假设磨料水射流单次铣削时的工件横截面形状为余弦曲线，建立了磨料水射流单次铣削的最大深度模型，分析了水射流压力、磨料流量、靶距、喷嘴横移速度、横向进给量和喷嘴直径及材料性能参数对单次铣削最大深度的影响规律。

The transmission properties of crown gear coupling are analyzed comprehensively. The crowning curve and the gear parameters are optimized.

本文较全面地分析了鼓形齿联轴器的传动特性，提出了鼓形齿轮鼓度曲线及齿轮参数优化设计新方案。

The main works of this paper are as follows:(1) The various methods for determining the cryolite ratio of electrolyte were summarized and compared. The phase constituents of aluminium electrolyte system were studied, the various cryolite ratio definitions for this reason were discussed.

本文研究和测定了工业铝生产中与电解质相关的几项重要的物理化学参数，包括铝电解质分子比的测定研究，氧化铝溶解性能的研究及测定，氧化铝浓度的测定及工业铝电解槽氧化铝浓度—槽电阻曲线的绘制，铝在电解质中溶解度的研究及测定。

This algorithm changes the detect points on the target trajectory to the respective curve in parameter space, which takes full advantages of the target detect data in a certain period, and the trajectory characteristics can also be picked up even under low SNR.

该算法把航迹上的观测点变换为参数空间的对应曲线，充分利用一段时间内的目标观测数据，在低信噪比下也能从背景噪声中提取目标的航迹特征，提高了声呐的检测概率，且对部分信息和数据的缺失不敏感。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新