参数变化

In present work, the coincidence Doppler broadening spectra of positron annihilation radiation of NiTi, NiAl alloys, single crystal of Si, and pure metals, such as Fe, Co, Al, Nb, Cu, Ni, Ti have been measured.

利用正电子寿命谱参数研究了NiTi合金马氏体转变及其奥氏体转变过程中的微观缺陷和电子密度的变化，从而揭示NiTi合金马氏体转变的微观机制。

Following on the GATF Color reproduction test chart to make some brief account, according to the patrterns function is divided into six major areas: simple color wheel graph is used to distinguish between colors and restore color detection; contact copy control standards section, you can use to test the print process changes in dot; dot number comparison chart, used to select and screen resolutions and paper and putting it in a match for reference, but also reflects the various color version modulational cards and membership cards making parameter is set to reproduce the effect and measurement; whether it is a normal RGB: neutral gray balance control chart; gray balance, this work out Y, m, C; proofing control bars.

下面对GATF彩色复制测试图作一些简单的介绍，按图谱功能分为六大区域：简易色轮图用于辨别颜色和检测色彩还原情况；接触拷贝控制标准段，可以用来检测晒版过程中网点的变化情况；网点线数比较图，用于选择网屏线数和纸张适性的匹配参考，也可反映各色版调制卡和会员卡制作参数的设置作用和测量子再现情况是否正常；三原色中性灰平衡控制图；灰平衡卡，依此算出Y、M、C的比例；打样控制条。

Based on Reddy higher-order shear deformation plate theory and general von Kármán-type equations, the analytical solutions for free vibration and dynamic response of simply supported functionally graded plates with piezoelectric layers in thermal environments are described with double Fourier series, where temperature-dependent material properties are taken into account.

基于Reddy高阶剪切变形理论和广义Kármán 型方程，用双重Fourier级数展开法求得了热环境下带压电层的功能梯度复合材料混合层合板的自由振动及动力响应的解析解，分析中考虑了材料热物参数对温度变化的依赖性，讨论了环境温度和控制电压对固有频率及动力响应的影响。

By comparison with experimental result (drift velocity v and randomness parameter r versus and external load f), it is shown that the model presented here can explain the available data rather satisfactorily.

并把计算结果(漂移速度v和随机参数r分别随和外力f的变化关系)同实验进行了比较，与实验值符合较好。

The changes of the pulmonary function parameters:lung resistance and dynamic lung compliance,were measured to evaluate asthma severity continuously.

实时测量哮喘豚鼠肺功能参数，肺动态顺应性和肺阻力的变化，作为反映哮喘严重程度的指标。

Changes in pulse parameters can be used as primary dysmenorrhea massage efficacy of reference for the evaluation.

脉图参数的变化可作为原发性痛经推拿疗效评判的参考依据。

By investigating the effect of all the factors, including particle size, density, elastic deformation coefficient, Hamaker constant, surface energy, yield limit and relative velocity, on the particle behavior in the process of collision, the rule of collision and agglomeration with the change of these factors is obtained in detail.

为考察包括颗粒的粒径、密度、弹性变形系数、Hamaker常数、表面能、屈服极限和碰撞初速度等众多因素对碰撞规律和团聚趋势的影响，本文采用"数值实验"方法，获得了碰撞力与范德华力的相互关系、碰撞弹性回复系数和团聚趋势随各参数的变化规律。

Exciting conduction Velocity of myocardium cells is one of main parameters which determine the body surface potential map and electrocardiography.

心肌细胞的电特性及心肌细胞间的传导关系决定了体表电位的分布及心电图的变化。心肌电兴奋传导速度则是影响心肌间兴奋传导关系的重要参数之一。

The purpose of this study was to compare and analysis the changes of walking on the slippery floor with three different high heels ( 3cm, 5.5cm, 8 cm) in kinematical, dynamics and lower limbs electromyographic parameters.

中文摘要目的：探讨女性穿著不同鞋跟高度（3公分、5.5公分、8公分）高跟鞋行走於光滑地面之运动学、动力学与下肢肌电图参数的变化情形与差异性。

The values obtained in thepresent study for the electron energy distribution function,drift velocity,ionizationcoefficient and attachment coefficient,etc.,are calculated and compared with theexperimental results reported in the literature,and the comparison is also carried outwith the values obtained from the two different types of fields.

应用Monte Carlo模拟法研究了氧气放电的电子参数，得到了在均匀电场中的电子能量分布、平均能量、漂移速度、电离系数、附着系数、迁移率及扩散系数随时间、电场强度的变化关系，并与文献上的实验结果进行了比较。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐