参数变化
- 与 参数变化 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Based on mechanism and vehicle theories theoretical analysis is pursued and normal driving conditions are put forward. The relations are analyzed between load distribution and power consumption. Mechanical formula is proposed. Furthermore in this paper the theoretical model of the total power consumption is established, and the relations of the total minimized power consumption with the air-cushion pressure and the fan revolution are discussed. The optimum operation point is put forward. The dynamic digital simulation studies are carried out on the operating procedure of the half-track air-cushion vehicle on soft terrain. Mechanical parameters and soil mechanics characteristics affecting vehicle power consumption and riding performance are analyzed. At the same time according to the model formula, the automation control problem is discussed. It is a theoretical instruction for further automation control.
本文还从力学和车辆原理的角度进行了理论分析,推导了半履带式气垫车的需求功率及正常行驶条件,研究了气垫压力和功率消耗之间的关系,提出了力学模型公式;建立了半履带式气垫车总功率消耗的理论模型,研究了最小功率消耗时功率与垫压及表征气垫车行驶状态的各参数的关系,分析了相应的影响因素,并提出了最佳工作状态的定义;同时进行了半履带式气垫车在软地面的行驶过程的动态数字仿真试验研究工作,对影响车辆功率消耗和行驶平顺性的各力学参数和土壤参数进行了分析,得到了各运行状态参数的变化规律,验证了最佳工作状态和最佳垫压的理论,根据力学模型公式对进一步的自动控制问题进行了探讨,为系统的控制提供了理论指导。
-
The results show that all these three factors are helpful to increase the alcoholysis degree,but the influence from the amount of alkali contributes the greatest,and the influence from the reaction temperature is the least.
结果表明,三种参数的增加都会使产物的醇解度增加,其中碱物质的量比的影响最大,其次是反应时间,反应温度对产物醇解度的影响最小,几种参数对醇解反应的影响是交互的,当其中一种参数发生变化时,其它几种参数的影响能力会随之发生改变。
-
Under toxic load shocking, The PGANN found by the database of UASB acclimated by the toxicant could be applied to predict the dynamic variation of the UASB been not acclimated. The PGANN found by the database of the UASB been not acclimated could also be applied to predict the dynamic variation of the UASB acclimated by the toxicant.
毒物负荷冲击下,在未驯化的UASB反应器上建立的PGANN可用来预测驯化过的UASB反应器各参数的变化,在驯化过的UASB反应器上建立的PGANN也可用来预测未经毒物驯化的UASB反应器各参数的变化。
-
This paper presents an IFMC CAD model that consits of a geometry model and a material model, in which the geometry space acts as a base space and the material space acts as a bundle space. In this CAD model, the geometry model is based on the non-manifold model. In addition, a half-face data sturucture, which is derived from the half-edge data structure with the non-manifold feature of IFMC taken into account, is adopted to represent the geometry and topology information of the component. For the material model of IFMC, this paper focuses on the FGM component representation firstly and present a simplex-subdivision based CAD data exchange format, in which the material information is represented as a (n-1) simplex and material distributing feature is represented by the interpolation on the simplex-subdivision. Based on those, a part-building orientation optimization algorithm and an adaptive slicing algorithm for FGM component are presented in the paper. For the IFMC material model, the IFMC material information representation is divided into a meso-scale and a macro-scale representation. In the meso-scale, a concept named parameterized periodic functional meso-structure is presented as a unique form to represent the FGM (the homogeneous materials are regarded as a special FGM), the composite and the functional meso-structure material. The model of PMS is a three-tuple that contains the space state informatation, the material parameter and the material meso-scale distribution feature. The macro-scale material information representation is similar to the FGM components by interpolation of the control parameter of the periodical functional meso-structure based on the simplex-subdivision. Through an example of manufacturing-oriented IFMC CAD data processing, it is proved that the IFMC CAD model and the material information representation and process method proposed in this paper can provide a reliable data support for IFMC digital concurrent design and manufacturing.
本文将理想材料零件CAD模型建立在以几何空间为底空间、以材料空间为丛空间的结构上,使用非流形几何模型作为理想材料零件几何拓扑模型的基础,并在半边数据结构基础上,针对理想材料零件的非流形特征局限内部边界上的特点,给出了一个半面数据结构来表述零件的几何拓扑信息;对于理想材料零件的材料模型,本文先从功能梯度材料零件的信息表述与CAD数据交换和处理入手,将材料信息表述为(n-1)维单纯形,然后通过对三维几何区域的单纯剖分,以插值的方式表述零件材料分布特征;在此基础上,根据功能梯度材料零件分层制造中对CAD数据处理的要求,给出了综合考虑零件几何特征与材料特征的生长方向优化算法和自适应切片算法;而对于文中所定义的理想材料零件,本文将其材料信息表述分解到细观和宏观两个尺度进行,首先给出了细观尺度上参数化的周期性功能细结构概念,以此来统一表述功能梯度材料(单质材料作为特殊的功能梯度材料看待)、复合材料和功能细结构材料;把周期性功能细结构模型化为一个包含空间状态信息、材料构成参数和材料细观分布特征参数的三元组,以表达零件的细观材料特征;对于零件宏观的材料变化特征,则同样在几何区域单纯剖分的基础上,通过对细观尺度上周期性功能细结构控制参数的插值来完成;通过理想材料零件CAD数据处理的算例,验证了本文中理想材料零件CAD模型及材料信息表述与处理方法完全可以为理想材料零件的数字化制造提供可靠的数据支持。
-
This paper presents an IFMC CAD model that consits of a geometry model and a material model, in which the geometry space acts as a base space and the material space acts as a bundle space. In this CAD model, the geometry model is based on the non-manifold model. In addition, a half-face data sturucture, which is derived from the half-edge data structure with the non-manifold feature of IFMC taken into account, is adopted to represent the geometry and topology information of the component.For the material model of IFMC, this paper focuses on the FGM component representation firstly and present a simplex-subdivision based CAD data exchange format, in which the material information is represented as a (n-1) simplex and material .distributing feature is represented by the interpolation on the simplex-subdivision. Based on those, a part-building orientation optimization algorithm and an adaptive slicing algorithm for FGM component are presented in the paper.For the IFMC material model, the IFMC material information representation is divided into a meso-scale and a macro-scale representation. In the meso-scale, a concept named parameterized periodic functional meso-structure is presented as a unique form to represent the FGM (the homogeneous materials are regarded as a special FGM), the composite and the functional meso-structure material. The model of PMS is a three-tuple that contains the space stateinformatation, the material parameter and the material meso-scale distribution feature. The macro-scale material information representation is similar to the FGM components by interpolation of the control parameter of the periodical functional meso-structure based on the simplex-subdivision.Through an example of manufacturing-oriented IFMC CAD data processing, it is proved that the IFMC CAD model and the material information representation and process method proposed in this paper can provide a reliable data support for IFMC digital concurrent design and manufacturing.
本文将理想材料零件CAD模型建立在以几何空间为底空间、以材料空间为丛空间的结构上,使用非流形几何模型作为理想材料零件几何拓扑模型的基础,并在半边数据结构基础上,针对理想材料零件的非流形特征局限内部边界上的特点,给出了一个半面数据结构来表述零件的几何拓扑信息;对于理想材料零件的材料模型,本文先从功能梯度材料零件的信息表述与CAD数据交换和处理入手,将材料信息表述为(n-1)维单纯形,然后通过对三维几何区域的单纯剖分,以插值的方式表述零件材料分布特征;在此基础上,根据功能梯度材料零件分层制造中对CAD数据处理的要求,给出了综合考虑零件几何特征与材料特征的生长方向优化算法和自适应切片算法;而对于文中所定义的理想材料零件,本文将其材料信息表述分解到细观和宏观两个尺度进行,首先给出了细观尺度上参数化的周期性功能细结构概念,以此来统一表述功能梯度材料(单质材料作为特殊的功能梯度材料看待)、复合材料和功能细结构材料;把周期性功能细结构模型化为一个包含空间状态信息、材料构成参数和材料细观分布特征参数的三元组,以表达零件的细观材料特征;对于零件宏观的材料变化特征,则同样在几何区域单纯剖分的基础上,通过对细观尺度上周期性功能细结构控制参数的插值来完成;通过理想材料零件CAD数据处理的算例,验证了本文中理想材料零件CAD模型及材料信息表述与处理方法完全可以为理想材料零件的数字化制造提供可靠的数据支持。
-
With the map for example, we can obtained following conclusions: the cam turning speed has the most direct influence to the dynamics of valve rain; the cam profilers has also a very important influence, the cam profiler as the kind of compound pendulum dose not suit to high speed engine's valve train and the polydyne cam's characteristics is very different from compound pendulum cam's.
论文还首次利用多质量模型的特点对气门落座速度、气门落座冲击力及落座反跳等气门落座特性参数随凸轮轴转速和结构参数的变化规律进行了研究,考察了不同凸轮型线对上述特性参数的影响。对气门落座特性参数进行这样详细和全面的研究,是本论文的开创性工作之一,在其他的文献中尚未见相同报导。
-
Taking the gradient property of piezoelectric parameters g-(31),elastic compliance parameters S-(33) and density ρ along z direction into account,some parameter identification methods for a functionally gradient piezoelectric material are studied in the present analysis.
当考虑压电材料的压电参数g31,弹性参数S33和材料密度ρ沿厚度呈梯度变化时,通过测量压电材料悬臂梁在电场或横向集中力作用下梁的宏观反映,给出了确定这些参数分布的公式,包括g31、S33的单参数识别及体积力与联合参数识别的方法。
-
LC filter is an important part of this hybrid reactive power dynamic compensation. The parameters of capacitor and inductive winding of LC filter change during operation with the changing surrounding temperature, the self-heating and the insulation ageing of capacitor, etc. During the installation and commissioning, there may exist errors that can deviate the actual parameters and correspondent harmonic oscillation frequency from the designed value and result in filter disarrangement.
LC滤波器是动态无功补偿装置中的重要组成部分,由于它的电容器和电感线圈参数,在运行过程中会因周围温度的变化、自身发热和电容器绝缘老化等因素影响而发生变化,在安装和调试过程中会存在误差,从而使实际参数和相应的谐振频率偏离设计值,导致滤波器失谐,这就要求对滤波器进行优化设计。
-
And the further relation of these parameters is obtained by the transient response. Results show that the parameters of the PID control method for the system satisfy the following rules: the proportional parameter is larger than the derivative parameter, and the derivative parameter is larger than the integral parameter.
结果表明:为了满足数字电子气动式座舱压力变化速率和稳定性的要求,PID参数需满足一定的关系:在一定范围内,控制器的比例参数应大于微分参数,而微分参数应大于积分参数。
-
The canopy structure and leaf morphological characters of 4 sugarcane genotypes at different leaf layers on seedling were studied by using CI-100 plant canopy instrument and CI-203 area meter instrument. The results showed the leaf morphological parameters, canopy structure and radiation transmission at different leaf layers were notably different among different genotypes. The variation of Ila, Amfi, Dl at different leaf layers were mainly caused by the leaf width at relevant position. The variation of K at different leaf layers was related to Amfi and Dl. The variation of Td(transm. coef. for diffuse penetration)had significant correlations with Ila, Amfi and Dl. The variation of Tr(transm. coef. for radiation penetration)had significant correlations with Dl, leaf width and the ratio of leaf length to width. The variation of Par had significant correlations with Ila, leaf area, leaf width and the ratio of leaf length to width.
摘要利用CI-100数字植物冠层分析仪和CI-203叶面积分析仪测定了4个甘蔗品种不同叶位层的冠层参数和相应叶位叶片的形态特征,结果表明:不同基因型不同叶位层间叶片形态、冠层空间结构和冠层辐射特征存在显著差异,不同叶位层叶面积指数、叶簇倾角和叶分布的变化主要由冠层内不同叶位叶片叶宽的变化引起,而不同叶位层消光系数的变化主要与叶簇倾角和叶分布有关;散射光透过系数的变化主要与叶面积指数、叶簇倾角和叶分布有关,直射光透过系数的变化主要与叶分布、叶宽、长宽比有关,光合有效辐射的变化与叶面积指数、叶面积、叶宽、长宽比有关。
- 推荐网络例句
-
With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.
随着死亡的吉他手Schuldiner接受主唱的职务,乐队在现实中树立了重要的影响。
-
But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.
不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐,因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。
-
Closes the eye, the deep breathing, all no longer are the dreams as if......
关闭眼睛,深呼吸,一切不再是梦想,犹如。。。。。。