参数传递

A method to identify the damping parameter s of machine joint surface is proposed based on the tested frequency response functions.

提出一种基于实测传递函数矩阵来识别机械结合面阻尼参数的新方法。

In chapter3, information is divided into two basic types, the marginal equation of bond price and short-term interest variations is established, thus the security price variations and the price equilibrium of other assets (risk security non-risk security are included) are analyzed by the implement of portfolio Theory.

第三章将债券的价格均衡划分为两大基本类型，建立了债券与短期利率变动的边际方程，运用组合原理分析债券价格变动与其它资产（包括风险证券和无风险证券）的价格均衡关系，通过比较收益原理建立了债券以市场均衡收益为折现参数的价值方程，并通过实证检验了该模型的合理性；第四章，分析了内部信息与价格的传导原理，建立了非完全信息市场条件下价格传递信息的做市商模型和预期模型，并讨论外部信息与内部信息对股票价格影响的非一致性。

In chapter3, information is divided into two basic types, the marginal equation of bond price and short-term interest variations is established, thus the security price variations and the price equilibrium of other assets (risk security non-risk security are included) are analyzed by the implement of portfolio Theory. Finally the bond value equation which takes equilibrium return as its yield Parameter is established through the theory of comparative return. In chapter 4, the intra-information and the transferable system of price is emphasized and the market-maker model and expected model under non-perfect information market conditions are established, and the disaccord of the influence of extra-information and intra-information on the security price is discussed.

第三章将债券的价格均衡划分为两大基本类型，建立了债券与短期利率变动的边际方程，运用组合原理分析债券价格变动与其它资产(包括风险证券和无风险证券)的价格均衡关系，通过比较收益原理建立了债券以市场均衡收益为折现参数的价值方程，并通过实证检验了该模型的合理性；第四章，分析了内部信息与价格的传导原理，建立了非完全信息市场条件下价格传递信息的做市商模型和预期模型，并讨论外部信息与内部信息对股票价格影响的非一致性。

By analysis and comparing with other kind of control system, according to the demands of the servo system for the Chamfering machines, the servo cylinder of the system was designed, the parameters of the opponents that was used for control and feedback in the system was calculated. Finally, the mathematics model of the position-feedback system was established, according to the model, the simulation frame was provided.

根据倒棱机对伺服控制系统的要求，通过分析及与其它控制系统的比较，设计了电液伺服系统的伺服油缸，确定了电液伺服系统控制及反馈元件性能参数，最后建立了位置控制闭环反馈系统的各个环节数学模型，并在此基础上绘出了伺服系统传递函数框图。

Then, safety analysis method was constituted considered the typical damage of concrete beam bridge. 5. By amending the reduction rate of loading capacity used in Code for Maintenance of Highway Bridges and Culvers (JTG H11-2004), a new reliable index is presented in the same safety standard to reflect the relation between load and resistance. According to the basic principal of calibration method, the recommended gradation index was computed under various factors such as different load combinations, vehicle operating status and different failure modes. With these calculated numerical values, the calculated reliability indexes standard for the estimation of safety degree of in-service concrete girder bridge members was ultimately obtained.6. Based on the related standards and results on crack and displacement that cannot continue to loading at home and abroad, the evaluation grade of the concrete beam bridge is proposed by analogy.

针对材料和构件损伤对混凝土梁式桥抗力的影响，基于材料和构件层次典型损伤的修正计算公式，在结构既有以及时变抗力评估的概率模型基础上，通过误差传递公式获得抗力统计参数，对抗力进行修正，构成了考虑混凝土梁式桥典型损伤的安全性分析方法。5、依据校准法原理，将《公路桥涵养护规范》(JTG H11-2004)中不同类别承载力下降率转化为修改分项系数，分别计算了轴心受压、轴心受拉、受弯、大偏心受压、受剪构件在各种情况下的可靠指标，根据破坏类型对校准结果进行分析，提出了基于可靠度的公路混凝土梁式桥安全性评定等级。6、基于不能继续承载的裂缝和位移的相关国内外规范和研究成果分析，通过类比提出了混凝土梁式桥不能继续承载的裂缝和位移评定等级界限。

Transmission rate of n+1 gametes is an important parameter for genetic analysis of trisomics.

n+1配子传递率是进行三体遗传分析的重要参数。

Transmission rate of n+1 gametes is an important parameter for genetic analysis of trisomics.

大白菜三体的n+1配子传递率的测定是利用三体进行遗传分析的重要参数。

Based on the processed accessory, the number, the position and the machining data of the holes and the form of the principal axis are determined; The driving way of the headstocks are drawn, the power is transmits by the methods of optimization, the driving parameter are determined, the structure of the principal axis are designed and the strength of the parts, such as the gears and the bears, are checked.

根据被加工零件确定加工孔的数量、位置、切削用量及主轴类型，拟订了主轴箱的传动方式，应用最优化方法传递功率，削减振动，确定传动参数，设计轴的结构，进行如齿轮、轴承等相关零件的强度校核计算。

These parameters include: substrate, roller, printing ink and its delivery.

这些参数主要包括：承印物、网纹辊、油墨及其传递。

Using the equation of broken line to define and substitutes for the signal transfer function, and the inverse function of approximate transfer function is obtained by way of the software method.

测量仪表由于元件参数的分散性和精度误差，使其被测物理量输入信号与输出信号间的传递函数为非线性超越函数。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。