参数

And objective parameters (texturized degree, color, hardness, springiness, chewing, water absorption, yield, etc.) were investigated in the high moisture soy protein extrusion process, and the statistical models of system and objective parameters were built, using the step-by-step regression analysis; A comprehensive evaluation of the products, and the process optimization of high moisture extrusion were obtained,using factor analysis; Secondly, residence time distribution and soy isoflavones losses kinetics were studied in the high moisture extrusion; Finally, chemical bonding process, the micro-structure and protein secondary structure changes were investigated in the texturization of soy protein, then the mechanism assumptions of texturization soy protein by moisture extrusion were proposed.

本文对大豆蛋白高水分挤压组织化技术和机理进行了研究，研究内容包括：首先采用系统分析法，研究了大豆蛋白高水分挤压过程中，挤压机操作参数(螺杆转速、物料水分、喂料速度和机筒温度)对系统参数(系统压力、扭矩、单位机械能等)、目标参数(组织化度、色泽、硬度、弹性、咀嚼性、吸水率、产量等)的影响规律，建立了各因变参数的统计模型；采用因子分析法对产品进行了综合评价，并对高水分挤压组织化工艺进行了优化；其次，研究了大豆蛋白高水分挤压中的停留时间分布以及大豆异黄酮的损失动力学；最后，研究了大豆蛋白组织化过程中化学键、微观结构和蛋白质二级结构的变化规律，提出了大豆蛋白高水分挤压组织化的机理假设。

According to the selected electric actuator determine the electrical parameters Because of different electric actuator manufacturers have different electrical parameters, design selection Butterfly Valves generally takes time to determine their electrical parameters, mainly electric power, rated current, secondary voltage control loop, are often negligent in this regard, the results of control system and the electric actuator parameter does not match the space-time caused by the work of opening trip, fuses, fuse, thermal overload relay protection is like a take-off and other failures.

根据所选电动执行器确定电气参数因不同电动执行器厂家的电气参数有所差别，所以设计选型时一般都需确定其电气参数，主要有电机功率、额定电流、二次控制回路电压等，往往在这方面的疏忽，结果控制系统与电动执行器参数不匹配造成工作时空开跳闸、保险丝熔断、热过载继电器保护起跳等故障现像。

The paper investigates both block-type pilot linear minimum mean square error algorithm and IEEE802.16 OFDM channel estimation analysis. Simulation results confirm the block-type pilot structure is more suitable for IEEE802.16 system. An optimal pilot setting algorithm, based on space frequency domain, is explored and the pilot chart is presented. The proposed algorithm finds its application in MIMO-OFDM. Simulation results show the algorithm presents a good approximation to the perfect channel state information curve, with about 2dB difference in SNR. The simulation results also demonstrate the algorithm achieves fairly high stability in the environment of fast fading, performance of the proposed algorithm is better that of pilot training channel estimation.3. Taking into account the characteristics of IEEE802.16 OFDM system, OFDM system simulation platform is constructed in Matlab, exploiting simulink as a tool. OFDM modulation and demodulation simulation system are configured on LabVIEW platform. All the system signal processing is simulated, including defining system parameters, designing modulation model, and verifying all the proposed algorithms under different environments, such as white Gaussian noise, multi-path fading, with or without guard interval etc. Bit error performance is evaluated. The research provides valid theoretical basis for practical OFDM system performance evaluation.4. Taking advantage of software radio, the paper designs a hardware platform with both 256-IFFT/FFT and 512-IFFT/FFT OFDM schemes co-existing in one platform. You can predetermine one from the two schemes to carry out almost the same model function with different system performance and parameter setting.5. Referring to IEEE802.16 standard, the paper proposes a design method for generating signals and frames suitable for laboratory investigations implemented in laboratory environment.6. Based on 6701evm digital evaluation card, combined with analogy front-end, the paper designs a DSP software model to deal with baseband signal processing. An overall OFDM scheme, with modulation and demodulation function, is accomplished.

讨论分析了MIMO-OFDM中一种基于空频域的最优导频设置算法，给出了导频图案，通过仿真实验表明，该算法与理想的信道状态信息曲线非常接近，信噪比差距约在2dB左右，并且在快衰落条件下具有较好的稳定性，其性能要优于基于前导训练的信道估计方法。3、根据IEEE802.16OFDM系统特点，论文分别在Matlab中应用Simulink工具构建OFDM系统仿真平台、在LabVIEW平台上实现了OFDM调制解调仿真系统，模拟了整个系统的信号流程，进行了OFDM仿真系统参数的选择和调制模块的仿真设计、论证各算法性能，并根据各种不同的条件：例如高斯噪声、多径衰落、有无保护间隔等，对系统的误码特性进行了评估，为正确评价实际OFDM系统的性能提供了有效的理论依据。4、论文以软件无线电思想作为指导，提出了以256点IFFT／FFT为核心和以512点IFFT／FFT为核心的两种OFDM算法模式并存于同一个硬件平台、且可预选的方案，它们在参数选取和性能指标上有所差异，均实现了相似的模块和功能。5、论文参考IEEE 802.16无线网络标准的参数设置，针对本设计系统的应用环境和系统硬件的性能速率，提出了一种应用于实验室环境的信号结构、帧格式等参数设计。6、论文基于TI公司的6701evm数字评估板卡，结合模拟前端搭建数字中频平台，设计了基带处理的DSP软件模块并进行系统调试，基本实现了一套完整的OFDM调制解调方案。

There are, however, no wide-accepted molecular parameters taken as a reference and no precise γ and A_D obtained simultaneously so far.

本论文报道我们获得的自然丰度下N~(16)O的中红外LMR光谱，并采用最新的联系各同位素分子参数的标度函数将所有已发表的光谱数据和我们测量的实验数据实现统一的标识分析，通过对所有数据的完整一体的最小二乘拟合，得到了迄今为止最完备、最精确的~mN~nO(m=14，15；n=16，17，18)系列分子的结构参数，这些参数的精度与文献结果相比提高了1-2个量级，其中许多参数都是首次获得的。

So the films completely meet the demands of IR detectors.The effects of deposition parameters on the performance of vanadium oxide thin films are analyzed by orthogonal experiments.

运用正交实验进行了工艺参数的研究，通过选择不同的工艺参数和不同的参数水平，得到了各工艺参数对薄膜性能的影响。

The interval finite element analysis method is extended from one-dimension truss member and beam structure to two-dimension plane structure.3 Genetic algorithm has powerful capability of global search and lower capability of local search, however, simulated annealing algorithm has powerful capability of local search and lower capability of global search.

5为了解某一参数的变化对结构响应的影响程度，提出了参数敏感性的区间分析方法，可以获得模型参数对决策目标的敏感性因子矩阵；通过对一平面应变结构地基模型的分析，得出了土体Duncan-Chang E_t-ν_t模型的八个参数的敏感性因子矩阵。

The method to configure RED parameters based on network properties is also presented. Simulations show that the modified Random Early Detection algorithm really performs better than the original Random Early Detection algorithm and can work for a much wider range of traffic. Finally, whether the assured service mechanisms i. e. an edge router tags every arriving packet of a TCP flow based service profile and core router drops packets differently at congestion using active queue management scheme is possible to provide a throughput consistent with target rate, is investigated under different network scenarios. Different factors including target rate tagged algorithm, RIO algorithm and TCP congestion control mechanism how to affect the throughput of an assured service TCP flow are examined. Based on a fluid model. we then derive a model of an assured service TCP flow, which is the function of round trip delay, packet loss rate and token bucket parameters. Based on this model, we observe that in some cases it is possible to regulate the token bucket parameters to gain a consistent throughput with the target rate, while in other cases there exist ranges of values of the achieved rate for which the token parameters have no influence. With the latter, some modified TCP congestion control mechanisms to assure TCP throughput are proposed.

最后，在区别服务网络结构内，研究了当前提出的一种边缘路由器根据服务合同标记、分类数据包，结合内部路由器采用主动队列缓冲管理机制区别处理数据包的确信服务机制是否可在不同网络情况下使TCP连接获得同目标速率相一致的、公平的吞吐量问题；指出影响TCP连接获得同目标速率相一致吞吐量的主要因素是目标速率大小、标记算法参数和TCP连接的拥塞控制算法；对此，基于流模型假设，首次推导出一个以端到端时延、数据包丢失率、漏桶参数为变量的确信服务TCP连接吞吐量模型；利用这个模型进行分析，得到主要结论是在一些情况下可通过设置合适的漏桶参数得到同目标速率更一致的吞吐量，而在另一些网络情况下不管如何设置漏桶参数都不能使TCP连接获得同目标速率一致的吞叶量；对于后一些情况，还初步讨论了改进TCP拥塞控制算法来改善TCP连接性能的方法。

According to the practical characteristics and parameters during hot finishing rolling process of aluminium alloy JP1235, a three-dimensional thermo-mechanical coupled elastic-plastic FEM model was established with the software Marc. And this model was used to simulate the rolling state of F1 stand without back tension. The lateral distribution of rolling force、contact friction force and other mechanic parameters were calculated. Meanwhile, simulated the rolling state considering the influence of mill tilt, and studied the distribution of the mechanics under this state, discussed the effect of mill tile on mechanic parameters and strip steering, which can provide some reference to steering control strategy.

根据JP1235铝合金板带热精轧过程的实际工艺特点和工艺参数，采用非线性有限元软件Marc，建立一个三维热力耦合弹塑性有限元模型，模拟了精轧机组第一机架（F1机架）失去后张力作用后的轧制状态，计算出轧制过程中轧制力、摩擦力等力能参数沿板宽方向上的分布情况，在此基础上，模拟初始轧辊倾斜影响下的轧制状态，并对该轧制状态下的力能参数分布情况进行研究，探讨轧辊倾斜对力能参数分布及跑偏规律的影响，为纠偏控制提供了一定的理论依据。

Through documents checking and data collecting,this paper analyzed the items and values of input/output parameters of N cycling in stock farming system,and ascertained the estimation parameters of N balance in the system,which could offer the theoretical foundation for nutrient management in animal husbandry ...

本研究对该系统的N输入、输出项参数进行分析讨论，包括平衡计算中每一个输入和输出项需要的参数种类、参数的选择以及建议采用的数值。讨论过程参考了大量的文献资料和统计数据，初步确定了我国畜牧系统N养分平衡计算参数。

Based on the characteristics of parameterized design and key technologies of knowledge based engineering, and specially according to the characteristics of the construction, figure, assembly-parameter of bicycle frame design, the article has achieved repeated using of experiential parameter and knowledge by adopting methods such as automatic reading experiential datasheet, computing parameter by making use of program, manual data-input or modifying and so on. Based on analyzing the characteristics of Rear End design and the associated characteristics with Chain Stay and Seat Stay, different design methods are analyzed in detail, and rapidly assembling of Rear End, Chain Stay and Seat Stay is achieved by using the method of combining top-down-assembly with down-top-assembly method. Based on analyzing special technologies and UDF characteristics, the repeated using of different sectional shapes by using UDF technology on the tube section design is also achieved, and this will greatly shorten the time spent on fixing the dimensions and orientations on sketches.

在探讨了参数化设计技术特点和知识工程关键技术的基础上，针对自行车车架设计中的结构、形状、装配参数特点，分别采用了读入经验数据表、参数程序求解、手工录入或修改方法实现车架设计经验参数和知识的重复利用；在分析自行车后叉片设计特点及与平、立叉的关联特性的基础上，对不同的设计方案进行了详细分析，并采用自顶向下和自底向上相结合的方法，实现了后叉片的快速装配定位与平、立叉设计相关联；在分析了特征技术和UDF特点的基础上，将UDF用于管件截面的设计上，使各种截面形状能不断重复利用，大大节省了约束草图尺寸和位置的时间。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。