原理

In this paper, compensation techniques of seismic simulation system are introduced primarily, including geometric cross coupling compensation, overturning movement compensation, off center load compensation and force balance compensation.

对振动台控制技术的台面补偿技术作了初步研究分析，其中包含几何交叉耦合补偿、倾覆力矩补偿、偏心负载补偿和力平衡补偿，并分析了它们的原理和电路实现原理框图。

According to the problem that grating scale hardly achieves high resolution when in high speed and the characteristic of high speed high precision system,this paper presents across dimension displacement measuring method based on dual grating scales dual measuring,the counting values of dual grating scales switch and merge.

在分析光栅线性位移测量原理、光栅尺的测量误差尤其是细分误差的基础上，本文重点研究双光栅尺切换与合成的原理，建立了基于双光栅尺高速高精度位移测量的设计准则，根据设计准则设计了切换基准拾取方法以及快速切换与合成方法，分析了双光栅计数值切换合成的误差。

A novel ultrafast SOA model is presented and the numerical arithmetic is provided.Secondly, an analytical formula for wavelength conversion of transient cross phase modulation is deduced from the viewpoint of impulse response function.

概括全文的研究成果和贡献，有如下几个方面：(1)研究了SOA实现全光信号处理的基本原理，推导了SOA中最基本的光场传输方程和载流子速率方程，分析各种非线性效应的原理及其应用。

S. pump wavelength and pump power were discussed.Secondly, the spectrum broadening due to the cross phase modulation in DSF was analyzed, and the principle and experimental setup of actively mode-locked Erbium-doped fiber laser was introduced.

第四章对交叉相位调制效应导致频谱展宽的原理进行了分析，介绍了主动锁模掺饵光纤激光器产生锁模脉冲的原理及实验，对基色散位移光纤交叉相位调制的波长转换进行了实验研究。

To study the calibration accuracy of stuctured light system based on cross-ratio invariant,measuring error and light-plane calibration error of system are analyzed,and an error propagation model is established by employing theories of error and matrix disturbance.

针对基于交比不变原理的结构光光平面标定方法，利用误差分析理论和矩阵扰动原理分别对系统的测量误差和光平面标定误差进行分析，提出了结构光测量系统的误差传递模型。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述砬冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：大直径三通管冲压复合模设计盖世了肥直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模与盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作砬简略概述；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：肥直径三通管冲压复合模设计盖世了大直径三通管的加工难题、带後浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模与盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展标的目的作了简略概说；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具举行了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工困难的问题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、圆环弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装配设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对于冷冲压技术的分类、特点及成长方向作了简略概说；论述了冲压零件的形成原理、基本模具结构与运动过程及其预设原理；对于典型的冲压件模具进行了预设：大直径三通管冲压复合模预设盖世了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模预设、适力压边式落料拉伸切边复合模预设、消音器后补碗落料、拉深、冲孔、翻边复合模预设、一模两件落料拉伸冲孔翻边复合模预设、圆环弯曲件的模具预设、铰链卷圆成形工艺及模具预设、半自动送料切角装置预设、滑板式送料拉深、冲孔、翻边模预设实现自动送料、长管多孔冲模预设、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：大直径三通管冲压复合模设计解决了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。