厚度

It was also found that the strength of FF specimen is close to the sumation of the strengths of FC and FS specimens with the same board thickness and screw spacing as FF specimen. As compared the test results with the research findings from Li [2]and Luo [3], It can be concluded that the failure mode of specimen is affected by both the sheathing thickness and the stud thickness. Different from this study, the failure mode of Li's test specimens is torsional-flexural buckling for most cases. The predicted values computed based on the AISI Specification seem to be conservative as compared to the tested values of FF specimens. Therefore, it is suggested that the effective length factor, K, can be taken as 0.5 to determine the wall stud assembly strength.

在三种不同试体组合分析时也发现，具外覆材支撑之立柱与外覆材受压内含支撑之立柱，两者之破坏强度相加，约等於具外覆材之墙体之破坏强度；试验结果与李岱真、罗浩之研究比较后，发现不同厚度之立柱与不同厚度之矽酸钙板之间束制关系明显影响强度之差异，且李岱真之试体破坏模式多为整体扭转-挠曲挫屈破坏，与本研究有较大差异；对於具外覆材之墙体与AISI预测值比较后，AISI规范预测值较保守，因此本研究有效长度系数建议采用0.5。

On the basis of the former researches and taking into account the practice of our country, this paper take the low period repeat loading experiment for three rigid conjunction node of steel beam and concrete wall, researching their load-bearing capacity and earthquake resistance performance under the low period repeat loading action, the main content concentrate on the following aspects:(1) Analyzing the three joint's damage shape、hysteretic curve、change of rigidity、yielding load、limit load、damage load、durability、energy dissipation capacity、the strain of the key position and the moment transferring mechanism.(2) Comparing the joint's load-bearing capacity and earthquake resistance performance among the joints with different stud bolt diameter and different connection plate thickness, researching some factor's influence on the work performance of the joint such as the high and strong stud bolt specification、connection plate thickness .

本文在前人研究的基础上，结合我国的实际情况，对3个钢梁-混凝土墙刚接节点试件进行了低周反复荷载试验，对其在低周反复荷载作用下的承载力和抗震性能进行了研究，内容主要集中在以下几个方面：(1)对3个节点试件在低周反复荷载作用下的破坏形态、滞回曲线特性、刚度变化、屈服荷载、极限荷载、破坏荷载、延性性能、耗能能力、关键部位的应变分布情况及节点核心区的受力情况进行了试验研究和理论分析；(2)比较了不同螺栓规格和不同连接板厚度的节点试件的承载力和抗震性能，研究了高强螺栓规格和连接板厚度这2个因素对节点工作性能的影响；(3)介绍了光纤光栅传感技术在土木工程领域中的应用研究现状及其基本原理；并通过对比试验，探讨了光纤光栅传感器用于土木工程检测的可行性及实现途径。

The terrace widths and step densities increase with increasing the GaAs layer thickness and then saturates.

原子力显微镜测试表明：在常规分子束外延情况下，GaAs外延层台阶的厚度和台面的宽度随衬底温度的升高而增加，增加外延层厚度会导致台阶的密度和台面的宽度增加然后饱和。

Under the conditions of keeping other design parameters constant, design thickness of valve flap increases with the mass increment on single wheel spring of the vehicle; throttle gap of oil-air spring is in linear decrement relationship with mass on single wheel spring. For each mass increment of 100kg on tested single wheel spring, design thickness of throttle valve flap will increase by 0.007mm and the throttle gap will decrease by 0.001mm.

在其它设计参数保持不变的情况下，阀片设计厚度随车辆单轮簧上质量的增加而增加；油气弹簧节流缝隙与单轮簧上质量成线性递减关系；试验的单轮簧上质量每增加100kg则节流阀片设计厚度将增加0.007mm，节流缝隙将减小0.001mm。

Take Kunming male small rat 40, random cent is 4 groups, be spent according to the strut of small rat ear of xylene be caused by and ply differs those who analyse every groups of medicaments to fight phlogistic action; to take Wistar male bandicoot 40, random cent is 4 groups, according to phosphoric acid constituent amine is opposite ply of area of splash of cutaneous of the back after bandicoot of Yiwen La Zaomo, skin and skin are deliquescent the convergent effect that the optical density influence at acetone solution analyses every groups of medicaments.

取昆明雄性小鼠40只，随机分为4组，根据二甲苯所致的小鼠耳肿胀度和厚度差分析每组药物的抗炎功能；取Wistar雄性大鼠40只，随机分为4组，根据磷酸组织胺对伊文氏蓝造模大鼠后背皮肤的色斑面积、皮肤厚度和皮肤溶解于丙酮溶液的光密度影响分析每组药物的收敛功能。

Using Brian ADI algorithm, the model is solved numerically and a snow-melting simulation program is developed based on the compiler of Visual Basic. This program can output some important results including the pavement temperature field, the height of snow layers, the height of liquid film and the idling characteristic curve.

通过Brian ADI格式算法，对上述模型进行数值求解，并基于Visual Basic平台，开发了一个通用型的道路融雪模拟分析软件，可输出路面温度场、雪层厚度、液膜厚度以及路面待融特征曲线等重要结果。

The rapid solidification power technology and the controlled atmosphere bonded technology are utilized manufacturing for high property Silver-Copper bimetal strips.

采用快冷雾化制粉技术和可控气氛复合技术生产高性能的银铜复合带材，可以连续大卷重进行生产，所生产的复合带材厚度比均匀，复合界面清洁、复合强度高，电性能良好，并可根据客户的要求生产不同厚度比和机械性能的带

In this thesis three kinds of piezoelectric transformers are investigated, including circular cylinder piezoelectric transformer of thickness-shear mode, cylindrical thin shell piezoelectric transformer of torsional mode and multi-layered rectangular plate piezoelectric transformer of thickness-twist mode.

本文研究了三种不同结构模态的压电变压器，包括基于厚度剪切模态的圆筒结构压电变压器、基于扭转模态的壳结构压电变压器和基于厚度扭转模态的多层矩形板结构压电变压器。

The TiO2 thin film on quartz glass is prepared by Liquid Phase Deposition method. The thicknesses of the films are determined by a spectrophotometer. The influence factors on the thicknesses such as ultrasonic vibration, times of sedimentation, sedimentation time and concentration of TiO2 colloid are investigated. A mathematical model of sedimentation is set up on the basis of gas adsorption theory.A photocatalytic continual tub reactor is set up.

本论文介绍了纳米TiO_2光催化降解甲醛的机理；用液相沉积法在石英基片上制备出纳米TiO_2薄膜，利用分光光度计间接测量TiO_2薄膜厚度，研究了超声波震荡、胶体浓度、沉积时间及沉积次数对薄膜厚度的影响；借鉴气体吸附理论，初步建立了制备TiO_2薄膜的沉积动力学模型。

Then the self-learn algorithm of deviation of gap zero is adopted for overcome the influence of the small variation caused by roll wear, roll expansion and mechanical clearance on gauge calculation.

根据中厚板的轧制特点，建立了比较完善的轧件出口厚度的软测量方法，它考虑了辊系弹性变形的影响，并引入辊缝零点漂移自学习算法，修正了轧辊磨损、热膨胀和机械间隙变化带来的影响，使轧件出口厚度的软测量模型更加完善。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。