厚度

Based on the calculation methods of nominal water-cement ratio of mortar and average paste thickness of standard sand provided by authors, the nonlinear relation between fluidity of mortar and nominal water-cement ratio of mortar, average paste thickness of standard sand, fly ash-binder ratio was established by using artificial neural network.

摘要在给出水泥胶砂名义水灰比和标准砂平均浆体厚度计算方法的基础上，采用人工神经网络方法，建立了水泥胶砂流动度与水泥胶砂名义水灰比、标准砂平均浆体厚度、粉煤灰与胶凝材料用量比之间的非线性映射关系。

The results show that the sensitivity increases with the scintillator thickness, and for the same thickness, the slope of energy response curve does not change greatly with the increase of neutron energy.

结果表明探测器的灵敏度随着晶体厚度的增加而增加，对于一定厚度的薄闪烁体，随着中子能量的增加，探测器的能量响应曲线坡度不大。

First of all, according to the business card printing and membership card making products classified as: cyclophos phamide, thickness of the carton with the Corporation's current ~ CCDs used, hardness is 35-38, 42; plastic bags with version 2.84mm, 228 ~, hardness of 50 ~ 60 scleroscope a; three parts, flexible packaging and labels version 1.14 ~ 1.70mm, hardness is 60 ~ 70.

首先根据制卡和会员卡制作品分为：①纸箱用版，厚度3.94～7mm，不不硬度为 35～42；②胶袋用版，厚度2.28～2.84mm，不不硬度为50～60；③不不硬包装和字号用版1.14～1.70mm，不不硬度为60～70。

The residual stress in the thickness after one LP and multi-LP and the distribution of residual stress after single pill and multi-pills shot the sheet metal are analyzed.

数值模拟分析了激光单点喷丸板料后，材料厚度方向的残余应力分布，以及激光多点。多排喷丸板料后材料厚度方向的残余应力分布。

Then use the same way after measuring coating photographic silk-screen reduced thickness, the two worst layer thickness.

再用同样的方法测量涂布感光胶后的丝网厚度，两者减差就是胶层厚度。

Because of being shear forming process, the relationship between the thickness ofthe deformed region, the thickness (t0) of the raw sheet, and the angleαbetween sheetmetal forming surface and vertical direction z conforms to the sine law, i.e.,t = t0 sinα.

由于金属板料数控渐进成形工艺的变形是剪切变形，故其板料变形区厚度 t 、板料初始厚度 t0及半锥角α等三者的关系符合正弦定律，即 t = t0 sinα。

All slip-on flanges are to be double welded with both welds built up to the thickness of the nozzle neck

所有的滑套法兰应是双焊接式，且两侧焊缝厚度为接管颈厚度。

When rolling the roadbed, the best degree of compaction is 93%~95%. When taking Aeolian sand for preventing the water rising, the Aeolian sand replacement should be set above water table, which should normally be made at 50~80 cm depth of soil base with 15~20 cm thickness of replacement for medium wet subgrade and 20~30 cm for wet subgrade. When using stabilized soil inorganic binder for prevention and control of the frost damage, the thickness of the binder is about 25 cm The mass proportion of cement, coal and Aeolian is about 6:40:54 and lime, fly ash and aeolian is about 14:30:56. Based on these, comparative evaluation for various preventing and curing measures of the Aeolian subgrade was given.

通过对试验数据分析得到了其冻结规律，采用碾压击实法，其最佳压实度度为93%~95%；采用风积砂换填隔水法，风积砂垫层时位置应在地下水位以上，一般应在土基50~80 cm深度处铺筑，换填厚度在中湿路基为15~20 cm，潮湿路基为20~30 cm；采用无机结合料稳定土防止、防治风积土路基道路冻害，厚度均应在25 cm左右，其中水泥、煤渣、风积土的质量比约为6：40：54，石灰、粉煤灰、土三者的质量比为14：30：56，在此基础上，对各种措施的防治效果进行了对比评价。

Through comprehensive analysis of many researchresults about movements of soil water and salts and data about effective root zone from literature,it was determined that the appearance of silt clay loam layer or silt clay layer with more than60cm cumulative thickness or more than 20cm continuous thickness in the 0~100cm soil horizonwas one of the most important indicator for soil series classification.It was also determined thatthe solum structure patterns of 0~150cm were another important indicator for soil seriesclassification.

通过对大量有关土壤水分、盐分运移规律的研究成果和有关土壤根系活动空间的研究资料的分析整理，确定了0~100cm土体中出现累积厚度＞60cm或连续厚度＞20cm的粉砂粘壤土层或粉砂粘土层作为土系划分的重要指标之一；并有根据地确定土表至150cm的土体构型作为土系划分的重要指标。

Packing gauge: A measuring instrument which is used to determine the space between plate, or blanket, and the cylinder bearers and thus, the amount of packing needed.

衬垫厚度计：测量仪器。用来测量印版，胶布和圆筒肩铁间的空位，因此而决定衬垫所需的厚度。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐