厚壁的

The effect of parison temperature gradients on behavior of parison inflation and part cooling further influence distributions of final part wall thickness and part quality.

由于型坯温度分布直接影响型坯吹胀行为和制品冷却，从而影响制品最终的壁厚分布和制品质量。

The parison thickness for extrusion blow molding has direct effects on the manufacturing cost of hollow plastic parts.

中空挤出吹塑型坯壁厚尺寸直接影响塑料容器的制造成本。

Conventional CT showed 44 cases of edematous type, dynamic contrast enhanced CT found 28 cases had different degree of necrosis of the pancreatic tissue, 6 cases were found to have focal hemorrhage, peripancreatic fluid accumulation were found in 32 cases, pseudocyst were found in 3 cases, abscess in 2 cases.

常规平扫显示胰腺水肿44例，动态增强扫描显示28例出现不同程度的胰腺组织坏死，6例检出局灶性出血；胰周液体聚集32例；假性囊肿3例，脓肿2例；伴胆石症15例，胆囊肿大或胆囊壁增厚22例；胆急管扩张12例，胰管扩张5例；胸腔积液11例。

Culms scrambling; internodes 20–30 cm, stiffly strigose; wall less than 8 mm thick. Branches many, subequal.

秆蔓生；节间的20-30厘米，硬具糙伏毛；壁厚不到8毫米；分枝很多，近等长。

The nail has the outer diameter of 10mm and 2 mm wall thickness to fit the normal Chinese tibiae.

骨钉的外径采用10mm、壁厚2mm以适用於一般国人。

By means of trepanning drilling a tiny hole was acquired, in which the diameter of entry was 240μm, the diameter of exit was 233μm ...

试样材料选用45#钢，壁厚为0.5mm，打孔形式采用环切法，最终得到入口240μm、出口233μm、圆度小于10μm的小孔。

Because of the above disadvantages this gate is seldom used for mouldings with walI thicknesses below 4 mm (0.150 in).

由于以上缺点，这种浇口很少在壁厚小于4mm（0.150in）的塑件上使用。

Movement is powered by hidden electric motors on 'bogeys' integrated into the wall thickness.

运动是由电动机的隐藏'忌'融入壁厚。

E. thickness of the copper wire wall, length of the single conductor wire, height of the solenoid, the exciting current and the current density, the working temperature of the conductor, time of exciting and demagnetizing, the cooling water pressure and flux density, etc..

所建立的数学模型包含3个目标函数（即能耗极小化目标函数、铜耗极小化目标函数和纯铁用量极小化目标函数）、7个设计变量（即铜管规格参数a、b、t，线圈匝数N〓、N〓，铁铠磁通密度B〓和冷却水压p）和8类14个约束条件（即铜管壁厚、单饼导线长度、螺线管高度、激磁电流与电流密度、导体工作温度、激退磁时间，冷却水压和铁铠磁通密度等约束条件）。

Dimensions, thread gaging, minimum wall thickness and burst pressure, material classification, various quality aspects and requirements for marking identification are stipulated.

尺寸，螺纹规，最小壁厚和爆裂压力，材料分类，各种质量要求和所规定的标记和标识要求等。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。