压铸模

Professional design, development, production, die-casting molds and die casting products.

公司专业设计、开发、生产、压铸模具及压铸产品。

I is a company specialized in the design and manufacture of die casting, casting the production, processing as one of the new enterprise.

我公司是一家专业从事压铸模具设计制造、压铸产品生产、加工为一体的新型企业。

The structures of solid a phase of original billet, pierce block in the chamber of die-casting machine, ingate block in die-casting mould and specimens atdifferent locations in a semi-solid die casting component were observed.

实验观察了原始料坯，压铸机压室内的冲头料坯以及压铸模内的内浇口和半固态压铸零件中不同部位的固相α组织的形貌。

The boundary conditions and the latent heat of heat transfer system have been treated by heat-enthalpy method.

在这样的充填条件下，虽然金属压铸模的导热性很高，蓄热能力很强，但要求在压铸模型腔内获得形状完整、轮廓清晰、尺寸精度高的铸件，必须得选用合理的模具结构和压铸工艺，而压铸模具的尺寸精度和使用寿命在很大程度上取决于其在压铸过程中热应力和其产生的变形。

The experiment of hot dip aluminizing had been carried out in order to study the interaction between die casting die and aluminum alloy and the effect of Si on soldering tendency between die and aluminum alloy casting.

为了研究压铸模与铝合金的相互作用，探讨Si对压铸模与铝铸件焊合倾向性的影响，进行了热浸铝试验。

According to researching technical speciality of Al-Si-Cu alloy,making choice of fit clearance of die casting mould shaped part is necessary,then in virtue of mould temperature-controller and midway anneal measure gains the results of increasing quality of die casting and prolonging service life of mould.

通过对铝硅铜合金工艺特性的研究，提出选定合理的压铸模成形零件配合间隙的必要性，并借助模具温控装置、模具中间退火等工艺措施，达到既提高压铸件的质量，又延长压铸模使用寿命的目的。

The thermal expansion deformation of die-casting dies during the compression casting process will affect the die parts fitting relation and lead to jamming or sticking of moving component s.

压铸模在压铸过程中由于受热膨胀变形，导致模具零件之间配合关系发生变化，出现运动零件的&卡滞&，甚至&粘着&现象，无法正常地连续生产。

And the designing method, naming and application of the standard die set s of the die_casting die were introduced.

分析了企业内部制定压铸模模架标准的必要性，介绍了压铸模标准模架的设计方法、命名及应

A new die-casting die fit on cold chamber die casting machine was redesigned in the part of the center gate and floating flow-distribution.

分析了录音机芯飞轮压铸模的原设计失败的原因，重新设计了用于冷室压铸机的中心浇口、浮动分流的压铸模。

This research sets the target of zinc die-casting design, the craft parameters parts crafts analysis, the choice of die-casting machines and platoon Yak system design, the introduction of institutions, national aircraft design, shape parts design, structural components design, die-casting mould technical requirements and material composition, a total of nine chapters.

本课题研究的对象是锌套的压铸模设计，包括工艺参数的选择，零件的工艺分析，压铸机的选用及排溢系统的设计，推出机构，模架的设计，成形零件的设计，结构零件的设计，压铸模的技术要求及选材等，本课题的设计论述出了各部分的设计方法与原则以及计算设计过程和必要的强度校核。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。