压缩性的

A performance prediction model is established in this paper which taking account into gas compressibility and the change of cross section area of flow channel.

本文建立的性能预测模型考虑了气相的可压缩性和沿流道的截面面积的变化，介绍了数值模拟的方法和步骤。

Art of figuration of the protruding after classics skin centrum (Percutaneous Kyphoplas-ty, PKP) is to be in art of figuration of classics skin centrum (Percutaneous Ver-tebroplasty, the technology of small innovation of surgery of a rachis that the development on the foundation of PVP) rises, its fundamental is the buy inside preexistence centrum enters but expansile ball bursa , the dilate that carries ball bag forms a cavity inside centrum, again infuse stuff stuff, correct deformation thereby, achieve constrictive to a few osteoporosis or tumour centrum that bring about fracture (Vertebral Compressionfractures, the remedial purpose of VCFs).

梗概： 经皮椎体后凸成形术(percutaneous kyphoplas-ty，PKP)是在经皮椎体成形术(percutaneous ver-tebroplasty，PVP)的基础上发展起来的一项脊柱外科微创新技术，其基本原理是先在椎体内置入一个可膨胀性球囊(inflatable bone tamp，IBT)，通过球囊的扩张在椎体内形成一个空腔，再注入填充材料，从而纠正畸形，达到对一些骨质疏松或肿瘤等导致的椎体压缩性骨折(vertebral compressionfractures，VCFs)的治疗目的。

In this paper, the dynamic equation of thin axisymmetrical shell involved rotation angle has been derived by lagrange equation using semi-analytical method.

本文采用半解析方法，利用拉格朗日方程，重新推导了包括转角在内的旋转薄壳的动力方程；利用加权余量法导出了壳内流体的考虑了压缩性影响的运动方。。。

Based on the hypotheses that the tissue fluid and the cell in lacuna are incompressible,and the tissue fluid could flow between the lacunar through the canalicular,the pressure on the cell was obtained.

基于骨陷窝中组织液和细胞具有的不可压缩性，以及组织液通过骨小管在骨陷窝之间的流动，得到了细胞所受压力的新的表达式。

Use instead and fasten and dig the bit to remove the hole and bottom eluvial soil after 5m (if the rock meeting high hardness while the base rock creeps into, can is it inlay rock bit get into to designing requirement hole dark by fastenning and digging and fighting the clear hole and then to use instead), in order to improve the strength of bearing the weight of of one , put the reinforcing bar cage finally , build the concrete.

本工艺基本上适应于各种土层，如软弱土层、松散杂填土、粉土、砂土、粒径不大（10cm以下）的碎石土和圆砾及其它塑性不大、粘粒较少的粘土，尤其适用于软塑、流塑、孔隙比大、高压缩性、抗剪强度小等特性的淤泥质土及因地下水丰富造成泥浆护壁困难的土层。

Reinforced Earth is, therefore, a composite material, combining the compressive and shear strength of compacted granular fill with the tensile strength of horizontal, inextensible reinforcements.

因此，加筋土是一种复合材料，它将经碾压的粗粒回填土的压缩性和剪切强度与横向无伸展性的加固材料的抗拉强度相结合。

Based upon SIMPLEC algorithm of CFD analysis, air film flow in the oil-free air bearing is simulated to illustrate its working principle, as well as performance's influence from air compressibility, shaft eccentricity ratio, clearance size and rotating speed.

基于计算流体动力学中的SIMPLEC算法，从流动模拟分析的角度对动压气膜轴承的工作机理，包括气体可压缩性，轴承间隙大小，轴颈偏心率及轴承运行线速度的作用等作了分析。

Based on the compressibility, viscosity resistance and the working house system's deformation etc, flow equations of distribution spool, hydraulic tube and fluid cylinder for 300 MN die forging hydraulic press were established, and dynamics equations of moving beam and upper beam were established based on analysis. The dynamics mechanical-hydraulic coupling model of driving system was established.

考虑流体的可压缩性、粘性阻力及工作框架系统变形等因素，采用解析法建立300 MN模锻水压机动梁驱动系统分配阀口、液压管道、液压缸的流量方程以及动梁和上横梁的动力学方程，得到驱动系统的动态机液耦合模型。

Based on the compressibility, viscosity resistance and the working house system's deformation etc, flow equations of distribution spool, hydraulic tube and fluid cylinder for 300 MN die forging hydraulic press were established, and dynamics equations of moving beam and upper beam were established based on analysis. The dynamics mechanical-hydraulic coupling model of driving system was established.

摘 要：考虑流体的可压缩性、粘性阻力及工作框架系统变形等因素，采用解析法建立300 MN模锻水压机动梁驱动系统分配阀口、液压管道、液压缸的流量方程以及动梁和上横梁的动力学方程，得到驱动系统的动态机液耦合模型。

The movement of plunger piston,the compressibility of the liquid and the leakage in the clearance between the plunger piston and pump barrel were comprehensively considered,and a new continuous flow equation of the fluid in the pump cylinder was setup.

综合考虑柱塞的运动规律、泵筒内流体的可压缩性、柱塞与泵筒之间的间隙漏失量，建立了泵筒内流体流动的连续流方程。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐