压盘

Insertable with flange plate,zinc die casting/steel, zinc-plated

锌合金压铸件/钢，镀锌，带轮缘盘，可以插入型材

S202 insertable with flange plate,zinc die casting/steel, zinc-plated

0.113kg w 锌合金压铸件/钢，镀锌，带轮缘盘，可以插入型材

The stability was increased by reducing the side load on the bit.The field applications in Lipan indicate that this new PDC bit has better performance i...

在临盘区块多口定向井的现场应用表明，新型定向井PDC钻头滑动钻进时钻压变化的敏感度小，工具面可控性好，复合钻进机械钻速和定向井机械钻速较常规PDC钻头都有较大幅度提高，且提高了钻井和下套管效率及井身质量。

Some other possible causes are a water logged air cushion tank, an over pressurized diaphragm style air cushion tank, an undersized air cushion tank and, on systems with a domestic water coil, a leak in the tankless coil.

其他可能的后果包括：气垫罐可能被浸透，受压过大的隔膜类气垫罐，气垫罐尺寸太小，带有室内水蟠管的系统，在无罐盘管内的泄漏，等等。

Shape dough into walnut sized balls, and roll them in the remaining 2 tablespoons of sugar. Place the cookies 2 inches apart onto an ungreased cookie sheet, and flatten slightly.

把生面团捏成许多胡桃状小球，在剩下的2桌匙白砂糖里面滚几下，以5厘米的间隔摆放到非油性的饼干烤盘上，轻轻压平。

While with the Coriolis force omitted, the flow in the cavity is under the influence of centrifugal buoyancy force, which can develop from stable to unstable as this force enhances. The centrifugal buoyancy force could lead to flow unstably.

哥氏力垂直于〓与〓构成的平面，对径向速度导致切向作用力，对切向速度导致径向作用力，在该力的作用下盘腔内轴向通流诱导的旋涡被压扁，尽管涡强有所增加，但是盘面的平均换热基本减弱。

All pressure part welding on inner vessel not otherwise fully radiographed shall have root and cover passes subjected to magnetic particle inspection.

对于没有进行全面RT 的内层容器上所有受压件焊缝（不包括夹套，但包括盘管），第一层焊道和盖面焊道需要进行MT检测。

All pressure part welding on inner vessel not otherwise fully radiographed shall have root and cover passes subjected to magnetic particle inspection.

不另行说明的所有内部受压件焊缝（不包括夹套，但包括盘管，此处应为COIL），根部焊缝进行RT，盖面焊缝进行MT检测。

In order to determine further the profile of scrolls,the structural characteristics of superchargers with double-sided scrolls were analyzed and the principle of determining initial involute angle s was presented on the conditions of definite initial involute angle s,radius of base circle,and depth of scrolls.

在渐开线起始角、基圆半径和涡旋齿深度确定的条件下，为进一步确定涡旋齿的齿形，对双侧涡旋增压器的结构特征进行分析，提出始端渐开角的确定原则。通过吸气腔和排气腔的容积计算，结合回转角与渐开角的关系，给出涡旋齿始端和终端渐开角的计算方法。结果表明：该计算方法能较准确地确定涡旋盘的结构尺寸，从而可估算出整个压气机的尺寸是否满足汽车上有限的安装空间

I Sales of products: submersible pumps, axial flow pump, Francis pumps, centrifugal pumps and other electrical equipment and related launch, motor, V-belt, the belt was, hoist, iron gates, piping, etc.; blenders, winch, welding Machine, cutting machine, Jack, hydraulic forklift, hoist, diesel generator, air compressor, electric wires, cables, sales of used construction tools, waterproof material, blankets and other oil.

我中心销售的产品有：潜水泵、轴流泵、混流泵、离心泵等及配套启动电器设备、电动机、三角带、皮带盘、启闭机、铸铁闸门、管路等；搅拌机、卷扬机、电焊机、切割机、千斤顶、液压叉车、葫芦、柴油发电机组、空压机、电线，电缆、销售常用的建筑工具，防水材料、油毛毡等。

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！