压点

Based on the basic solutions of the pressure response of point source in infinite space, pressure responses at any point in a horizontally infinite reservoir are studied.

以无限空间点源压力响应的基本解为基础，研究了水平方向无限大油藏在任意位置的压力响应，从测压点位置、等价压力点、多解性的解决办法等方面探讨了水平分支井的试井解释方法。

The problems in the application of electric contact manometer pressure leveling system are elaborated.

阐述了电接点压力表补水泵定压系统的一些应用问题，给出了电接点压力表定压点的上、下限计算公式，并提出了该系统补给水泵、补给水箱及安全阀的设计选型方

The steps of Reduced Gradient optimal method is used on solving the Least Squares theory model. At some situation, some nodes pressure and supply of all water-supply sources are measured in Xi'ning (resistance parameter of all pipes are known). By using the pressure of the experiment and optimal measure points, the state simulation is done respectively to get all nodes' pressure.

利用简约梯度优化法求解给水管网状态估计的最小二乘数学模型，实测某一工况下西宁市配水管网部分节点水压H_0、各水源供水量分别用优化选择的测压点水压和按经验选择的测压点水压估计所有节点的水压，对西宁市配水管网进行了状态估计。

The automatic stacking technology for the iron core of motor stator and rotor was presented,including the classification of stacking form,the geometry and distribution of skew riveting stacking compression points,the depth of stamping and the way of parting of iron core stacking.

通过对电机定子和转子铁芯自动叠装技术的介绍，将铁芯叠装形式的分类、扭斜铆接叠压点的几何形状、分布、冲压深度以及如何实现铁芯叠装的分台进行说明，提出模具设计时应注意的要点，对此类模具的设计有一定的参考作用。

The automatic stacking technology for the iron core of motor stator and rotor was presented,including the classification of stacking form,the geometry and distribution of skew riveting stacking compression point s,the depth of stamping and the way of parting of iron core stacking.

通过对电机定子和转子铁芯自动叠装技术的介绍，将铁芯叠装形式的分类、扭斜铆接叠压点的几何形状、分布、冲压深度以及如何实现铁芯叠装的分台进行说明，提出模具设计时应注意的要点，对此类模具的设计有一定的参考作用。

Block point, inductive point and lever are fixed in crust. The whole equipment was placed around the vein just like sleevelet.

利用血液在流动过程中对血管壁压力的差异，设计了阻断点和受压点，两者通过不等臂杠杆连接，固定于包裹囊内，整个装置如袖套式安置在静脉壁外。

Duty officer, now the ship is leaning to seaside, can you pump some ballast water into the shore side for balance?

值班副 ，现在船正向海侧倾斜，你能向岸侧压点压载水平衡一下吗？

Minimum holding pressure: based on the correct switch point, the pressurewhen the parts start to be empty .

最低保压压力：在准确的转压点基础上，给予一定的保压压力，当产品刚出现充模不足时的保压压力。

Minimum holding pressure: based on the correct switch point, the pressurewhen the parts start to be empty .

最低保压压力：在精确的转压点基础上，给予一定的保压压力，当产品刚呈现充模不足时的保压压力。

Minimum holding pressure: based on the correct switch point, the pressure

最高保压压力：在精确的转压点基础上，给予一定的保压压力，当产

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。