压应力

It is discussed that linear expansion coefficient of RCCP plate length and thickness has an influence on temperature stress.

探讨沥青混凝土罩面层厚度、碾压混凝土线胀缩系数、板长和板厚对温度应力的影响。

According to the failures of van-type filter press,stress analysis is presented for main components such as filter plate by finite element theory.

针对厢式压滤机在生产使用过程中的损坏情况，对滤板这一过滤过程中主要承载构件，用有限元的方法进行了应力计算。

In the present study, through using non-linear three dimensional finite element analysis, considering the contact in flange to nut and flange to gasket, we accurately computed the stress distribution in the flange joint in the normal work condition.

采用ANSYB软件，应用三维有限元技术，考虑了垫片的非线性和法兰和螺母、垫片的接触问题，并且采用了螺栓预紧单元，准确计算出法兰连接在承受内压、轴向力和弯矩外荷载时的应力分布。

In order to fully used the compression resistance of the concrete,this paper analyzed the stress distribution to the composite beam in the actual use,and put forward to the method calculating the concrete flange plate thickness.

为充分利用混凝土的抗压性能，本文通过分析钢与混凝土组合梁使用阶段的应力分布，提出了一种确定钢梁上混凝土翼板厚度的方法。

The results indicate that when soil and pile are same, the shear stresses between pile and soil under the ultimate situations of different modes are different; the negative friction on pile induced by surcharge is maximum; and the negative friction of uplift pile is minimum; the friction of pile top induced by pressing pile and bottom-loaded pile is between them.

结果表明，同种土体和桩体条件下，各种模式达到极限状态时桩－土间剪切应力不同，堆载作用下负摩擦力值最大，抗拔桩负摩阻力值最小，桩顶受压桩、托桩的摩阻力值介于其间；桩材泊松比在0.15~0.35范围内时，桩侧摩阻力随泊松比的增大而增大。

All mechanical loads are considered, including internal pressure, gravity, wind load and earthquake load, in which the modal analysis of the drum, functional wind load and temporal analysis for earthquake are the innovations of this paper.

分析焦炭塔在机械载荷，如内压、自重、风载和地震载荷作用下的应力情况，其中塔体的模态分析、风载的函数加载和地震载荷的时程分析是本文的创新。

To minimize, the stress is removed from the insulators, and materials with low piezoelectric effect are used.

若要减小压电电流，需要消除绝缘体的应力，并使用具有低压电效应的材料。

The paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects,such technologies as:manufacturing and fixing of reinforcement,steel reinforcement fixing baseplate,web plate and top plate respectively and lifting the steel skeleton into form,requirements of design and manufacturing and way of utilization for dismantling-erection type formwork and hydraulic formwork,optimization of concrete ratio,concrete pouring process of two ends of beam in priority over the middle,in sequence of first baseplate followed by web plate and top plate at last,concrete pouring in inclined section and in horizontal layer,concrete vibration mainly byexternal vibrator in assistance with internal vibrator,methods and regulation for steam curing of concrete,dual controls over stress and strain to ensure quality of prestressing workmanship,construction method of effective beam moving by heavy-weight special moving facility,some regulations and key notes about construction of grouting under pressure,beam ends sealing,water-proof layer on the bridge surface system,protective coating.

文中介绍的采用胎具制作和绑扎钢筋，分底腹板和顶板分别绑扎并吊装钢筋骨架入模；拆装式和液压式两种模板的设计、制作要求和使用方法；综合考虑、优化混凝土配合比，混凝土灌注从两端至中间、先底板、后腹板、再顶板的施工顺序和斜向分段、腹板水平分层、附着式振捣为主、插入式捣固为辅的施工工艺，蒸汽养护的方法和规定；应力～应变双控制确保预应力施工质量的施工技术；采用重物移运器有效移梁的施工方法；压浆、封端、桥面防水层和保护层施工的一些规定和注意事项等都是对箱梁制造行之有效的施工技术和施工方法，并可为以后类似施工作借鉴。

There aren't any pipe joints of integral valve, therefore it's not subject to pipe or bolt influence, pressure case will not be subject to "mutation" of pressure.

不带任何管接头的整体式阀体，因此不受管道或螺栓应力影响，并且由于阀体无任何管接头，故耐压壳体不会受压力&突变&的影响

The use of intermediate stiffeners in the compression plate may significantly increase elastic buckling stress and ultimate capacity of the plate.

在受压板件中设置中间加劲肋可以显著提高板件的弹性屈曲应力和极限承载能力，但是也使得板件的屈曲行为变得复杂。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。