压力的

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

It showed that the propane recovery rate of new process would be 23%~27% higher than that of cryogen refrigeration process at the same refrigeration temperature. To increase the absorption tower pressure appropriately was good to improve the propane recovery rate. However, the choice of pressure must take the pressure of the feed natural gas and product gas into account together. The flow rate of absorbent had great effect on propane recovery rate and tower heat load.

本文实例研究表明：相同制冷温度下，冷剂制冷－油吸收复合工艺的丙烷回收率比原冷剂制冷工艺可提高23%~27%适当提高吸收塔的压力，对增大丙烷回收率有利，但吸收塔压力的确定要综合考虑原料气压力和外输气压力的大小。

The thermodecomposition of Li〓CO〓 charge was experimented and studied in a specially made vacuum furnace. The relationship of decomposition rate with temperature, pressure and time were obtained. The important principle of decomposition rate effected by pressure was acquired and conception of critical decomposition-pressure was presented.

在特制的真空炉内对碳酸锂物料真空分解进行了试验，得到了分解率与温度、压力、时间的关系；得到了分解率受压力影响的重要规律，据此提出了分解临界压力的概念，总结出了分解临界压力与温度的关系。

The purpose of our work is that get the target and technique of pressure adjustment through the analysis of formation porous pressure that affects the quality of cementing, regulation of pressure change for infilling wells, technique of pressure dropping for whole block, technique of pressure discharge for high pressure, maintaining pressure in high pressure and lower penetrability formation.

突出的工作在于通过对影响固井质量的地层孔隙压力的分析得出压力剖面调整的目标，通过注水井降压规律、区块整体降压技术、高压层泄压技术、高渗低压层压力保持方法等几个方面研究提出一套压力剖面调整技术。

Under different source oil pressure, output pressure of reducing valve, some experimental investigation into the frictional characteristics has been done.

本文在不同的油源压力和减压阀出口压力的情况下，进行了摩擦特性的实验研究，得出了油源压力和减压阀出口压力的最佳关系。

The recovery and displacement efficiency of the matrix block dominated by capillary force is compared with that domonated by the couple of capillary and viscous force, and by viscous force.

在驱动压力和毛管压力的不同平衡(驱动压力和毛管压力的相对大小)关系下的水驱油采收率和水驱油效率的变化规律

With determining and comparing the result of the output of chlorine dioxide, the purity of chlorine dioxide, the rate of chlorine dioxide, the capacity of active chlorine and the output of chlorine generated by positive pressure type chlorine dioxide generator under different pressure, this paper draws the conclusion that the effect of pressure to aerogenesis efficiency of chlorine dioxide generator is indistinctive when the pressure is in the range of 0～0.6M Pa.

从化学平衡角度分析，压力增加会抑制正向反应的进行。为了验证实际效果是否如此，本文通过在不同压力下对正压式反应器 ClO2产量、纯度、得率及总有效氯产量等指标进行测定与比较得出，在 0～0.6M Pa的常用压力下，压力的变化对二氧化氯发生器的产气效率无显著影响。

In the paper, the factors of the pressure of gas-gathering pipes and high-pressured ammonia water was controlled unstably in the period of Linhuan Coking Limited Liability Company began to product were analyzed, then effective methods about how the coke workshop and chemicals workshop coordinate to control the pressure of gas-gathering pipes and high-pressured ammonia water well in production were made.

文章对临涣焦化股份有限公司投产初期集气管压力与高压氨水压力控制中的不稳定因素进行了分析，并对炼焦车间与化产车间在生产中怎样配合来做好集气管压力与高压氨水压力的控制提出了行之有效的方法。

Spring-loaded safety valve spring is delivered to the valve on the container or force to balance the pipeline pressure by adjusting the elastic springs to balance the medium on the pressure valve control media pressure to achieve the objective of safety valve lever weights Is to use a heavy hammer through the transmission lever to force the valve to balance the pipe or container medium pressure by adjusting the weights of the valve to balance the role of media from the valve on the pressure, media pressure to achieve the purpose of control ; Pilot of the main safety valve by valve components and sub-valve, to promote the role of Vice valve main valve action, also known as the pulse safety valve.

弹簧式安全阀是利用弹簧传递到阀瓣上的作用力来平衡容器或管道内压，通过调节弹簧的松紧来平衡介质对阀瓣的压力从而达到控制介质压力的目的；杠杆重锤式安全阀是利用重锤通过杠杆传递到阀瓣上的作用力来平衡管道或容器内介质的压力，通过调整重锤对阀瓣的作用距离来平衡介质对阀瓣的压力，从而达到控制介质压力的目的；先导式安全阀是由主阀和副阀组成，借副阀的作用带动主阀动作，又称为脉冲式安全阀。

Then, according to HVS, the vibrant valve is designed. On the basis of coupling analysis and simulation study of the vibrant valve and the release valve, the simulation curve about the fluid pressure variation in the pile-driving oil pipe is obtained, by which the relationships among the highest pressure value, average pressure value and the pile-driving frequency are obtained.

然后根据液压振动系统设计了振动开关阀，并重点对液压振动系统中的溢流阀和振动开关阀进行了耦合分析和仿真研究，得出压桩油路中流体压力变化的模拟曲线，并根据模拟曲线分析得出流体压力的最高压力值、平均压力值和压桩频率间的相互关系。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。