压下

A calculation of ideal gas under the saturated vapor pressure at different temperatures a small program.

详细说明：一种计算理想气体在不同温度下饱和蒸汽压的小程序。

But it is crowded, Ilex is, bending the waist down branches.

但它密密麻麻，满树都是，压得树枝弯下了腰。

In addition, at the above described experimental condition, the increase of the inactivation rate was 30%.

此外在试验条件下，由于压致升温导致的芽孢失活率的增加均在30%以上。

The large deformation for incompressibility rubber cylinder under inner pressure is considered by a kind of new rubber materials strain energy function.

针对一类新的橡胶材料应变能函数，推导了受内压作用下不可压缩橡胶圆柱的大变形公式，给出了位移、应力的解析表达式。

As a result, the contact area of Berkovich indenter will be larger and nanofretting damage will be weaker.

因此，Berkovich 压头在高载下具有更大的等效曲率半径，产生更轻微的纳动损伤。

Finally, the contact zone and contact stresses can be determined when a couple of contact loading and indenter's curvature are specified.

最后，利用所得直线族，在已知接触压力与压头半径的前提下确定接触区尺寸与接触应力。

Nano- and Micro-Hardness Testers（Nano Indentor/Micro Indentor）- Quantitative measurement of mechanical surface properties: elastic modulus and hardness - Analysis of fracture modes, cracking,… Nano- and Micro-Scratch Testers - Adhesion and anti-scratch properties of coatings and films - Profilometry Tribometers - High Temperature, Vacuum and Nano Tribology - Wear and Friction studies Calotest / Calowear - Coating thickness measurement - Wear rate testing 3D Imaging - Atomic Force Microscope - Confocal Microscope

动态压痕测试仪器为您提供纳米或微米尺度下材料的硬度、弹性模量、蠕变、断裂韧性等性质。我们还为您提供纳米级、微米级摩擦磨损测试仪器，用以测量材料的摩擦系数和磨损率。我们的球磨仪器是测量薄膜厚度最简单准确的工具。我们同时提供光学显微镜、原子力显微镜、白光共焦显微镜成像工具。我们在瑞士的分析测试中心随时准备为您提供高质量测试服务。

The conclusions can be drawn through numerical simulation: The hydrate-forming region becomes small with increasing circulation rate and inhibiter concentration, and it is possible to make the hydrate-forming region away from sea floor by increasing circulation rate and inhibiter concentration, thus preventing blowout preventer lines from hydrate plugging; the decrease in gas volume fraction in the annulus due to hydrate formation reduces pit gain, which can delay the detection of well kick; the possibility of hydrate presence at a relatively low gas production rate is much greater than that at a relatively higher production rate; the bottom hole pressure is affected little by hydrate phase transition, and it is allowable not to consider hydrate phase transition when the bottom hole pressure is calculated; shut-in casing pressure cann't truly reflect gas kick due to hydrate formation and the situation is getting worse with time

模拟计算结果表明：溢流期间，天然气水合物的生成区域会随着循环流量的增大或抑制剂浓度的提高而减小，可通过增大流量和抑制剂浓度使水合物的生成区域脱离海底，减小防喷器管线被堵塞的危险；水合物的生成使环空中气体体积分数降低，泥浆池增量减小，给溢流检测带来延迟；当检测到有气侵发生时，水合物藏分解速率比较小时，井筒中生成水合物的可能性要比分解速率大的情况下更为严重；水合物相变对井底压力的影响较小，在工程中计算井底压力时可以忽略；由于天然气水合物的生成使得关井套压值不能真实反应气侵情况，而且随着时间的增加情况会更加严重。

Secondly, Dynamic and quasi-static state mechanical properties experiments of hardened 45 steel and Fe-36Ni invar alloy are performed by Split Hopkinson Pressure Bar and electronic universal testing machine, the dynamic mechanical properties under high temperatures and high strain rates are obtained.

其次，采用分离式霍普金森压和电子万能试验机进行了淬硬45钢和Fe-36Ni因瓦合金的动态和准静态力学性能试验，得到了它们在高温和高应变率下的动态力学性能。

The result for an aluminum sphere with gaussian pulse incident wave was compared to the theor y value obtained by inverse Fourier transform from the product of Rayleigh serie s with incident wave in the frequency domain, which shows a good agreement.

计算了高斯形脉冲入射下弹性铝球的无量纲反向散射声压，并和由频域的Rayleigh 简正级数解与入射波的频谱的乘积作反变换得到的精确解做了比较，两者趋势基本一致。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。