压下

Combining with the National Natural Science Foundation ofChina(No.50478032), following researches were done in this thesis: 1 The variation regularity of the ultimate anti-bending capacity of therectangular-sectioned beam with different corrosion has been obtained through thequalitative analysis of 48 beams (32 corroded beams and 12 comparing beams) withaccelerated corrosion; 2 The conclusion has been obtained that the strain of corroded steel bar andconcrete no longer fit in with the assumption of plane section through the analysis ofthe strain data, the strain relation of steel bar and concrete in the mid-span section ofvariously corroded beams at ultimate has been obtained. Through the building of newgeometric relation, the expression of the height of compressive area in the corrodedbeam with rectangular section has been deduced, and the formula with corrosion rateas the main variable for the anti-bending capacity of the corroded concrete beam hasbeen suggested and verified by experiment.; 3 The influence of steel bar corrosion and the concrete regression to the flexureductility coefficient of the corroded structure component has been analyzed. Based onthe relation of steel bar and concrete at yield and ultimate, the expression for theflexure at yield and ultimate of corroded reinforced concrete beam, and the model forthe calculation of the flexure ductility has been built.

本文结合国家自然科学基金项目(50478032)"既有钢筋混凝土桥梁时变可靠度研究"，主要进行了以下研究工作： 1通过对48根快速锈蚀钢筋混凝土矩形截面梁(32根锈蚀梁和12根对比试验梁)数据的定性分析，得到了不同锈蚀率下，锈蚀钢筋混凝土矩形截面梁极限抗弯承载力的变化规律； 2通过对应变数据的分析，论证了锈蚀构件钢筋和混凝土的应变不再符合平截面假定的结论，并通过回归分析得出了不同锈蚀率的螺纹钢筋梁和光圆钢筋梁在极限弯矩作用下，跨中截面处钢筋应变和钢筋处混凝土应变的关系，通过构造新的几何关系，得出了锈蚀钢筋混凝土矩形截面梁计算受压区高度的表达式，既而得出了以锈蚀率为主要变量的锈蚀钢筋混凝土矩形截面梁的正截面抗弯计算建议公式，并通过试验数据加以验证； 3分析了钢筋锈蚀和混凝土劣化对锈蚀构件曲率延性系数的影响，结合钢筋屈服和极限弯矩两种状态下钢筋和混凝土的应变关系，分别得到了锈蚀钢筋混凝土矩形截面梁屈服曲率和极限曲率的计算表达式；既而推导出曲率延性系数的计算模型。

A prediction model has been proposed to deal with threshold voltage shift as a function of 1MeV neutron flux and gate oxide thickness, and to deal with room-temperature annealing of threshold voltage shift induced-by 〓Coγ as a function of electric field and gate oxide thickness. The commonness and individuality of MOS device degradation between hot-carrier effect and ionizing radiation were investigated. The dependence of substrate current, gate current and threshold voltage shift due to hot-carrier on gate oxide thickness were simulated with MEDICI-2D simulator. The photocurrents of PN junction and bipolar transistor were studied. Their transient responses on varied bias voltages, pulse durations and absorbed doses were simulated. The influences of NPN base width on base and collector photocurrents were investigated. We also studied 1MeV neutron displacement damage in PN junction, and calculated reverse current leakage under the neutron flux of 2. 67×10〓 per square centimeter. 3 The study of nondestructive screening method for MOS radiation tolerance A theoretical and experimental study of nondestructive screening methods for radiation tolerance of nMOS and pMOS were firstly fulfilled. We determined the informative parameters pertinent to the method and proposed how to deal with experimental data and verify obtained results statistically, as well as make the required steps for nondestructive screening. Based on the experimental data of 180 samples of discrete pMOS devices, the relation between sample quantity and correlation coefficient, screening equation, and other significant results were obtained from the threshold voltage shifts of pre-and post-irradiation samples.

二、分立器件电离和位移辐射损伤响应研究在国内首次开展了电离辐射引起的氧化层阈值电压漂移和退火理论研究，编程计算了1MeV中子引起的MOS器件阈值电压漂移与中子通量及栅氧厚度的关系，计算了〓Coγ光子引起的阈值电压漂移及退火的时效曲线与纵向电场和栅氧厚度的关系等，对评估MOS型集成电路电离损伤和加固方法研究，以及论文中开展的MOSFETs无损筛选方法研究奠定了基础；分析了MOS器件热载流子损伤效应与辐射电离损伤效应之间的异同性，利用二维模拟软件MEDICI-2D模拟了衬底电流和栅电流，在不同栅氧厚度下随栅压的变化曲线，计算了热载流子效应造成的阈值电压漂移，研究结果对当前存在的以热载流子效应研究取代电离辐射损伤实验研究的设想，具有重要的参考价值；开展了PN结和双极晶体管电离光电流研究，计算了不同偏压、不同辐射脉宽和不同吸收剂量下PN结光电流的瞬时响应，计算了不同辐射脉宽下NPN晶体管基极电流和收集极电流的瞬时响应，以及基区宽度对NPN晶体管光电流的影响，研究结果对双极器件抗电离辐射损伤响应及加固方法研究具有重要意义；在国内首次开展了器件位移损伤的理论研究，分析了辐射产生的缺陷对电性能的影响，计算了注量为2.67×10〓cm〓的1MeV中子产生的缺陷对PN结反向电流的影响。

With the compressional stress increasing,the dip-slip motion in listric fault system could successively generate reverse-"fish-fork-shaped" structure,hanging wall interpenetration thrust,footwall shortcut thrust,"backward broken" footwall shortcut thrust imbricated fan,"backward broken interpenetration" thrust,.

随着压应力递增，铲式断层系统中的倾向滑动可渐次形成反转-&鱼叉&状构造、上盘交截冲断层、下盘捷径冲断层、&向后破裂&下盘捷径冲断层叠瓦扇、&向后破裂交截&冲断层、向前破裂后冲断层叠瓦扇、后冲断层与下盘捷径冲断层扇形构造和脊部塌陷&上突&构造等。

By regression of experimental data, therules of the linkage between these factors, which will provide a theoretical basis for designing BBP with different scales.3 Using thermal analysis technology and dynamic thermogravimetry, the paper studies combustion kinetic characteristics of 3 types of agricultural crops at different rate of temperature rise, and thus, achieved dynamic parameters of these fuels at different rate of temperature, established dynamic model of straw combustion, which reflects the dynamic process in the fast combustion area.4 Characteristics of straw briquette combustion was experimented, focusing on the impact of straw type, temperature, air supply, and density, diameter, and weight of briquette on the combustion speed, and the following conclusions were drawn:(1) combustion of straw briquette fuel is static permeation diffusion combustion;(2) temperature has a larger impact on the speed of straw briquette combustion than air supply; the higher the combustion temperature is, the faster volatilizable component separates out, and the less steady the combustion is;(3) density of briquette fuel has impact on the speed of volatilizable component separation and therefore the combustion speed;(4) increase of diameter and weight of briquette fuel increases the average combustion speed in the initial stage, and that in the later stages is comparatively steady;(5) the proportion of volatilizable component in straw briquette fuel is high, therefore, the temperature control during combustion under the rational ventilation condition is essential to ensure its safe combustion.5 Using the above-mentioned results of experiments and theoretical analysis, and based on thought of hydraulic driven and bi-direction compression, the hydraulic system and compression parts of the HBP BBP are re-designed in terms of industrialization.

利用热分析技术，采用动态热重实验法，对我国的三大农作物秸秆在不同升温速率下的燃烧动力学特性进行了较系统的研究。得到了各原料在不同升温速率下的动力学参数；建立了秸秆燃烧的动力学模型，该模型反映了秸秆迅速燃烧区的动力学过程。 4 对秸秆成型燃料的燃烧特性进行了试验研究。着重研究了秸秆河南农业大学博士学位论文巫的种类、温度、空气供给量、成型燃料密度、直径、质量对成型燃料燃烧速度的影响并得出如下主要结论：①秸秆成型燃料的燃烧方式属于静态渗透式扩散燃烧。②秸秆成型燃料燃烧速度受温度的影响大于通风量燃烧速度的影响：燃烧温度越高，挥发分析出速度越快，燃烧平稳性愈差。③成型燃料密度影响成型燃料挥发分的析出速度，影响燃烧速度。④成型燃料直径和质量的增加，使得燃烧初期的平均燃烧速度增大，中后期的平均燃烧速度相对平稳。⑤秸秆成型燃料含挥发分比例高，因此合理配风下的控温燃烧是保证其完全燃烧的关键。 5运用已取得的试验和理论分析结果，以液压驱动、双向成型为基础，从产业化的角度对HBP型成型机进行了液压系统和成型部件的改进设计；同时采用了二级预压机构，使该成型机的生产率达到 500kg.hd；单位能耗 60kwh。上'左右，磨损件修复周期 300小时左右，基本解决了影响生物质固化技术在国内推广的技术难题。

Three types of base asphalt and six SBS were used to produce SBS modified asphalt. The interaction of SBS modified asphalt was discussed in different states between the base asphalt and SBS based on their compositions. Through the traditional tests, such as penetration, soften point and ductility, and US SHRP tests, the results indicated that influences to affect the temperature susceptibility, high and low temperature performance, aging characteristics are base asphalt, SBS types and their dosages. The functions of penetration to viscosity and complex shear modulus G~* to complex dynamic shear viscosity η~* were set up, and then theviscosity-temperature susceptibility of wide temperature span and the calculation method of low temperature viscosity were obtained."Process" evaluation criterions, high grading critical temperature T_ and low grading criticaltemperature T_ , were suggested according to the high and low temperatureperformances of SBS modified asphalt. Using the experience of Repeated Creep and Recovery Test for Binders, a new high-temperature evaluation index,modification rutting factor G~*~(-9) was obtained. The results after RTFO and PAV aging indicated that traditional tests didnt differentiate base asphalt and SBS modified asphalt, but dynamic mechanics temperature spectrum and G*-5 black chart clearly reflected the influence of aging to the SBS modified asphalt. With the IR and GPC tests, the reason of aging to the SBS modified asphalt were due to asphalt phase oxygenated and SBS phase depredated.

论文选择3种油源的基质沥青和6种SBS改性剂制备改性沥青，通过分析基质沥青和SBS改性剂的组成结构特点，得出了不同状态下SBS改性沥青的SBS与基质沥青的相互作用机理；通过针入度、软化点、延度等常规试验以及美国SHRP试验，分析了基质沥青、SBS改性剂类型与剂量对SBS改性沥青的温度敏感性、高低温特性及老化特性的影响；建立了针入度-粘度、复数模量G~*-复数粘度η~*的换算关系，得出了宽温度域的粘温指数VTS和较低温度下粘度的计算方法；通过高低温性能分析提出了&过程&评价参数高温等级温度T_和低温等级温度T_；借鉴重复恢复与蠕变试验研究成果，得到了SBS改性沥青高温评价指标改进型抗车辙因子G~*~(-9)；RTFO和PAV老化后的性能试验结果表明，常规试验难以区分SBS改性沥青与基质沥青的差异，而动态力学温度谱、G~*-δ黑斑图可以反映老化作用对SBS改性沥青的影响，且通过IR试验和GPC试验得出SBS改性沥青老化是沥青相的氧化和SBS的降解共同引起的；通过不同温度下SBS改性沥青混合料的旋转压实SGC试验，根据粘度与剪变率的关系，提出用剪变率60(1／s)测试SBS改性沥青的粘温曲线，并按照0.17±0.02Pa.s和0.28±0.03Pa.s确定施工温度。

The main creating aspects are finding and clarify such a fundamental physical process that the grain boundaries emit vacancies under compressive stress to induce solute non-equilibrium grain boundary dilution and absorb vacancies under tensile stress to induce non-equilibrium grain boundary segregation, formulizing the structural equations and the composition equations in force equilibrium in grain bounary region to describe this physical processes and the kinetic equations for non-equilibrium grain boundary segregation under tensile stress, calculating the modulus in grain boundary region from the expermental data of grain bounday segregation using the structure and coposition equations and calculating the diffusion coefficients of vacancy-solute atom complexes using the kinetic equation simulating the experimental results of grain boundary segregation.

本项目的主要创新点是，发现并阐明了弹性应力场作用下空位与晶界交互作用的基本物理过程：在张应力作用下，晶界会吸收空位，引起溶质非平衡晶界偏聚；压应力作用下，晶界会发射空位，引起非平衡晶界贫化。建立了描述此物理过程的晶界区力学平衡的结构方程和成分方程；？建立了张应力引起的非平衡晶界偏聚动力学方程？；用晶界区力学平衡的结构方程和成分方程？，首次通过实验测量计算出多晶材料晶界区的弹性模量；通过建立的动力学方程模拟实验结果，首次获得溶质原子－空位形成的复合体的扩散系数。

The main content included in the paper is as follows: The European identification methods of type of wave load is introduced and compared with the methods in Code of Hydrology for Sea Harbour. In order to reveal their difference, they are tested by the experiment data. The relation between phase and frequency are analysed through the Hilbert and wavelet transformations. And a new method of identifying the breaking wave load is set up based on the linear relation between wave height and wave press before the breakwaters. The probability distribution is tested by the statistic of experiment data. Based on the experiment data, the paper analysed the influence of reflection coefficient according to different factors, and its property is got. The work property of charmfered breakwater under breaking waves is analysed. Through the statisticof its wave press and wave force the distribution of press on the breakwater front face and its reducing effect to breaking wave force are proved.

本文基于此，通过实验研究，主要作了如下工作：介绍了欧洲波态划分方法，分析与我国方法的异同，通过实验进行了验证；通过 Hilbert 变换和小波变换对波浪破碎的相频特性进行了分析，通过建立波高与波压关系来判别破碎波浪力；对破波条件下波浪力的分布进行了统计研究，验证了其分布类型；利用实测资料，分析了不同因素对反射系数的影响，得出了不同周期、波浪要素、破碎率下反射系数体现的不同规律；分析了破碎波作用下削角堤的工作特性，通过对堤面所受的波压力和总力的统计分析，验证了压强分布规律及削角堤对波浪力的削减作用。

Systematic research about technology parameters influences on the magnetic properties and microstructure of theses magnets have been done. The better parameters of production have been achieved. They are showed as follows: as-cast alloys with the nominal composition Nd15Fe78-xNbxB7 are prepared by induction-melting under argon atmosphere. As-cast alloys are broken under argon atmosphere and filtered through 40# screen. The coarse grain is ball-milled under 120# avgas for 80 min. The ratio of milling ball and grain is 15:1. Then fine powder is aligned and pressed in a magnet field of 1.5T. The pressure is 80MPa. The green compacts then are shaped by cold isostatic pressing under 280MPa pressure.

通过研究具体工艺参数对磁体磁性能及显微结构的影响，总结出适合于该系列磁体的制备工艺如下：按设计成分将原料放入真空感应熔炼炉内进行合金铸锭的熔炼；合金铸锭在高纯氩气保护下粗破碎过40目筛；以15∶1的球料比在120#航空汽油的保护下滚动球磨80min；球磨好的磁体粉末在1.5T取向磁场下以80MPa的压力模压成型，接着在280MPa压力下进行冷等静压；所得的压坯在1110℃烧结1h，900℃回火处理1h，600℃回火处理2h。

The reservoir rock types in the region of interest are grain limestone, algal limestone, cryptite, siltstone, muddy limestone and mudstone. The thesis identified as a result of changes in the deposition causing the heterogeneity in plane, and then the geological oil reserves have been calculated in accordance with the areal heterogeneity.3、Based on the data of core analysis, bore logging, array induction imaging log and FMI, porosity and permeability model were built using regression analysis. Through testing 45 rock samples, a, b, m, n value were obtained and used to calculate single-layer oil saturation value using the Archie formula. According to the theory of laterolog and inductolog, resistivity ratio and cross plot were used to identification effective thickness. Effective thickness was identified delicately in 103 wells. Based on the over work, active porosity and oil saturation was calculated accurately.4、According to observation of 100 pieces of the thin slices, cast thin slices and 383m core in three wells, the chief diagenesis in this area were compaction, cementation, denudation and cataclasis. Cementation and denudation were universally influenced active porosity this area. The intergranular pores, residual pores and secondary pores were formed in thin carbonated reservoir of lacustrine facies.5、The influence of reservoir heterogeneity to reservoir calculation was analyzed systematically using actual data. And the conclusions were as follows:①The principal reason leading to oil distribution unequal is interior structural feature of reservoir in structural hydrocarbon reservoir.

确定了由于沉积微相的变化而导致的平面非均质性，进而在平面上按照平面非均质单元计算了石油地质储量。3、利用岩心分析、常规测井曲线与阵列感应、成像测井资料相结合，分岩性利用回归分析方法建立了储层孔隙度、渗透率模型；通过对45块岩样进行岩电试验，获取了a、b、m、n值，利用阿尔奇公式计算了各单层含油饱和度值；根据侧向电阻率和感应电阻率串并联特性，利用电阻率比值法与常规交会图法相结合重建了有效厚度图版，对全区103口井目的层段进行了有效厚度精细划分，通过以上工作，准确求取了储量计算单元内有效厚度参数、有效孔隙度参数以及含油饱和度参数。4、通过对研究区3口井383m岩心观察，100余块薄片、铸体薄片镜下鉴定得出：油泉子油田上、下油砂山组储层主要成岩作用是压实作用、胶结作用、溶蚀作用和破裂作用，其中溶蚀作用、胶结作用最普遍，这两种作用对有效孔隙度影响最大，以上成岩作用形成了原生粒间孔、粒间残余孔和次生孔隙(如粒间溶孔、粒内溶孔、铸模孔、晶间孔等)为主的薄层湖相碳酸盐岩储层。5、利用实际资料，系统分析了油藏非均质对储量计算的影响，认为：①对于构造油气藏而言，油气藏构造及断裂特征是造成油气分布不均的首要原因，储集条件相同的条件下，构造高部位有利于储存油气，油气在垂向的重力分异体现了油气藏内部构造的不均一特征。

As the flakes that fall thick upon a winter's day, when Jove is minded to snow and to display these his arrows to mankind- he lulls the wind to rest, and snows hour after hour till he has buried the tops of the high mountains, the headlands that jut into the sea, the grassy plains, and the tilled fields of men; the snow lies deep upon the forelands, and havens of the grey sea, but the waves as they come rolling in stay it that it can come no further, though all else is wrapped as with a mantle so heavy are the heavens with snow- even thus thickly did the stones fall on one side and on the other, some thrown at the Trojans, and some by the Trojans at the Achaeans; and the whole wall was in an uproar.

像冬日里的一场大雪，下得纷纷扬扬，密密匝匝――其时，统治世界的宙斯卷来飞落的雪花，对凡人显耀攻战的声势。他罢息风力，一个劲地猛下雪片，覆盖了山岳中迭起的峰峦和突兀的岩壁，覆盖了多草的低地和农人精耕的良田，飘落在灰蓝的海波里，遍洒在港湾和滩沿上，只有汹涌的长浪可以冲破它的封围，其余的一切全被蒙罩在白帐下，顶着宙斯卷来的大雪的压挤。就像这样，双方扔出的石块既多且密，有的飞向特洛伊人，还有的出自特洛伊人之手，扔向阿开亚人，整道护墙发出震耳欲聋的巨响。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐