压

Porosity declines exponentially inthe compaction portion,however porosity keeps constant in the elastic portion.

本文将岩石压实的全过程分成了压实作用段和弹性作用段。

The elastic deformation of the pipe and a certain amount of air filled within were considered.

建立了考虑管道弹性变形和含有一定量气体时输气管道严密性水试压稳压时间计算的数学模型。

And justified that the better crush is twice elastic limit crush.

证明较好的压扁量为弹性极限压扁量的2倍。

The concentration of hydrogen ion, voltage on electrobath and the temperature of electrolyte were the main factors affecting hydrogen production from indirect electrolysis of hydrogen sulfide and the voltage on electrolytic cell took a most important part in the process.

该模型在实验测量的范围内，得到了较好的验证；通过理论推导和实验验证，确立了硫化氢间接电解制氢中试阴极反应的主要影响因素为氢离子浓度、槽压和电解液温度，其中槽压的影响最大。

The results showed that,in actual operation,the device should be optimized based on the comprehensive consideration on the influence of electrolyzer voltage on every operation p...

结果表明，在实际运行中需要综合槽压对各种操作参数的影响而对其进行优化，槽压在3.5～4.0 V时，运行效果最佳。该实验为膜电解钠碱法脱硫的应用提供了依据。

In order to install the electrothermic Board, silica gel used for blocking the release version of silica gel used for blocking the General selection of grass-roots level to 1-3 mm in thickness of the aluminum plate. Silica gel layer from the aluminum plate between the bond strength directly linked to silica gel used for blocking the version of the service life, if the silican layer from the aluminum plate between the bond strength is not high enough, the high temperature and high pressure easy to crack.

当然，在本质操纵洋上述几个参数的设定不是白云苍狗的，而给根据本质处事洋的需给举行拔取和设定，如铜、锌版不同，平均的烫印压辛、较矮的烫印温量和较缓的烫印速率会爆发更抱负的烫印成果，因为平均的烫印压辛使电化铝的黏结性更好，较矮的烫印温量使电化铝的光华量更矮，而较缓的烫印速率是为了适答较矮的烫印温量。

Version before the electrothermic Board clean surface treatment and gilding, pressure on the back of the concaveconvex zinc version designated some skin, a milky white gum toppedwith of the slightly larger than zinc version of cloth version adocumented Zinc plate location and business card printing and membership card modes on the electrothermic, and then you paste in the electrothermic version of Zinc plate cloth top, at the end of platforms put some hard paper on closing and heating power connected to 80-90 ° c hot press about 15 minutes, so that the zinc version bridgeis the electrothermic Board.

装版前应将电热板表面处理洁净，并在烫金，压凹凸锌版背面划一些条痕，将一块涂有乳白胶的稍大于锌版的布块按确定的锌版装版位置和制卡和会员卡制作方式粘贴在电热板上，再将锌版粘贴在电热板布块上面，在底台板上放些硬纸合压，并将电源接通加热至80-90℃，热压15分钟左右，使锌版牢固粘贴在电热板上。

With a corporate logo and other marks that embossed paper known as pressure laid paper.

具有公司标志和其他标记的压纹纸张称为压纹纸。

GY also produces metal embosser machine , three roller calendering machine , plastic extrusion assembling machine , filming machine , plastic extrusion plate sheet production line , PVC plate sheet production line , embossing devices etc .

公司还生产金属压花机，三辊压光机，塑料流延膜机组，涂膜机组，塑料挤出板材生产线

Produces plastic artificial leather embossing roller,mirror roller,hot roller,anilox roller,oil heated roller,peripheral drilling roller for paper making machine、steel to steel calendering roller and rubber roller. gy also produces metal embosser machine,three roller calendering machine,plastic extrusion assembling machine,filming machine,plastic extrusion plate production line,pvc plate production line,embossing devices etc.

公司拥有大型精密机床三十六台套，电镀流水线三条，德国激光原装雕刻机贰台，全套电脑制版、分色、激光照排系统，台湾、日本引进的皮纹辊雕刻设备，年产各类压花辊（塑料人革压花辊、镜面辊、热轧辊、网纹辊、油加热辊、造纸机械周边钻孔轧辊、钢对钢对轧辊、橡胶辊）13000余根。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。