压

Licensing Laojun called Cha Cha Cha is not, but dozens of drugs selected food homology group of natural plant science from the regulator side Jiapin regulator.

老君牌舒压茶叫茶不是茶，而是精选数十种药食同源的天然植物科学组方而成的调压稳压佳品。

At the same time, we discussed the fittable field of deep convective impressible model comparing with the origional pressible equations.The result is that deep convective impressible model is close to the pressible model and is good to be used to simulate troposphere.

本文首先对中小尺度动力学进行理论探讨，特别是与本文有关的深对流不可压动力学模型，比较它与原始可压运动方程组的联系及其适用范围，表明在对流层的研究中使用浅对流不可压模型是不可行的。

As competitions between people have been intensified significantly over time, people's pressure has been increased dramatically. In order to release the pressure, people would like to do outdoor exercises on holiday. People get used to the life with water and electricity supply and rely on electronic products. Therefore, it is really inconvenient to exercise outdoor without the electricity supply. In order to solve such inconveniency, an innovational product is invented, and the name is called "Inverter."

随著人与人之间竞争越越激，人们的生活压与日俱增，平时工作压大，到假日就想走向户外，藉由各种的休闲活动舒解生活压，然而平时过惯有水有电的生活，对生活家电已是相当依赖，而家电用的是市电，当假日到郊外，没市电，就会产生许多困扰，为消弭远城市所产生的种种，於是就产生一种电子产品-----Inverter，Inverter其主要作用即是将直电转换成交电，其用意乃是运用、船或飞机上之蓄电池

Finite element method was used to explore the nanoindentation process of several materials under Berkovich indenter. The simulated nanoindentation results with different tip radii were compared with experiments.

采用有限元方法模拟了纳米压痕中不同曲率半径针尖的压头压入不同材料的加、卸载过程，并对计算结果与实验进行了对比以验证模拟的可靠性。

1 This test method is based on the penetration of a specific type of indentor when forced into the material under specified conditions. The indentation hardness is inversely related to the penetration and is dependent on the elastic modulus and viscoelastic behavior of the material. The geometry of the

4.1本测试方法是根据有关规定，将指定类型的压足压入测试材料进行测量的，反言之，硬度与压入量有关，同时又与材料的弹性模量和粘弹性能有关。

The influence of indentor radius on the plastic deformation has been discussed and some important results are as follows:(1) The influence of the ratio of ceramic coating thickness to indentor radius on the failure of coating, plastic deformation of substrate and crack propagation are obvious.(2)The propagation of crack in ceramic coating is assumes to be of semi-elliptical shape under normal contact with a rigid sphere.(3)Fatigue life of ceramic coating is mainly decided by substrate and load, the lower substrate elastic moduli and load, the more cycles of fatigue.

分析了压头半径对塑性变形的影响，模拟结果表明；(1)陶瓷涂层厚度和压头半径之比对涂层失效、基体塑性变形及裂纹的形成有显著影响；(2)在刚性球压头静态挤压条件下，陶瓷涂层中的预制裂纹按照椭圆形裂纹规律扩展；(3)陶瓷涂层的疲劳寿命与基体和载荷有很大关系，基体弹性模量越小，疲劳寿命延长。

2 Presser Foot, Types A, B, C, D, DO, E, O, OO, OOO, and OOO-S, with an orifice (to allow for the protrusion of the indentor) having a diameter as specified in Fig.

A型，B型，C型，D型，DO型，E型，O型，OO型，OOO型，OOO-S型的压足和配合孔的尺寸见FIG.1（a，b，c，d，e，f和g）的规定，压足中心与测量试样任意边缘最小距离为6.0mm（0.24in），当压足设计成圆形平面时，它的的面积不应小于500mm2 19.7in2

By using the"energy equivalent method",thepiezoelectric structure damping is equivalent to a viscosity damping,according to which the quantitative relationship between the response time ofan one-dimensional piezoelectric actuation system and the mechanical qualityfactor of its piezoelectric material.The inexactness of the previouscorresponding relationship obtained by Taylor is analyzed.

用能量等效法将压电结构阻尼等效为粘性阻尼，建立起一维压电致动系统的响应时间与压电材料机械品质因子之间的定量关系，分析了以前由Taylor所获得的定量关系的不严格性。

In this paper, an un-circular piezoelectric inclusion embedded in an infinite piezoelectric matrix is analysed in the framework of linear piezoelectricity.

本文以椭圆夹杂为例，讨论了在线性压电学范围内的无限压电基体内嵌有非圆形压电夹杂的反平面问题。

Chapter two presents the three-dimensional equations of the nonlinear theory of electroelasticty for large deformations and strong fields and the linear theory of piezoelectricity for infinitesimal deformation and fields.

第二章从连续介质力学理论出发，给出了适于压电研究的普遍的电弹性非线性理论，以及近似的三维线性压电理论和线性压电本构关系。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐