压

The embossment of this machine is conducted by electric-heating to stable temperature from steel roller to fiber roller, also other material of embossment roller can be adopted as per customer's request.

本机采用钢辊对纤维辊电热恒温压花，可根据要求采用其他材质压辊压花。

The embossment of this machine is conducted by electric-heating to stable temperature from steel roller to fiber roller, also other material of embossment roller can be adopted as per customers request.

本机采用钢辊对纤维辊电热恒温压花，可根据要求采用其他材质压辊压花。

It is found that under the same vibration mode, the equivalent inductance of the single layer piezoelectric transformer is the twice of the same quality piezoelectric oscillator; 2 Based on the density energy formula, the three-dimensional lump type equivalent circuit of the piezoelectric transformer has been set up.

发现在相同的振动模式下，单层压电变压器的等效电感是相同质量压电振子的两倍； 2）以能量密度公式为基础，建立了压电变压器的三维集总式等效电路图。

May be, and any model, specification supporting the use of filter press, filter press for the slurry to give the best matching filter press pump types.

可和任何型号、规格的压滤机配套使用，将浆料送给压滤机进行压滤的最理想配套泵种。

With these points,this topic will base on Finite Element Analysis and Research ofFlux detection with Press use ANSYS Flotran method.

本文以压差式瞬态流量测量为目标，围绕实现压差式测量中多点压力传感器设置间距问题进行了以下几个方面的工作：利用流体力学的相关理论，详细分析了利用压力传感实现瞬态流量测量的机理，推导了两点和三点式压差测量瞬态流量方法的相关公式，并对影响测量的相关因素进行了分析。

On equipments of system, this paper, making use of the finite element analysis function of CATIA V5, make Optimization analysis of the key components of the core equipments in the system, such as the side platen and the roller axis, and bring optimization Solutions.

在系统设备方面，本文运用CATIA V5的有限元分析功能，对系统中的核心设备——辊压机的侧压板和压辊轴等关键部件进行了优化分析，并提出优化改进方案。

This paper set out from the high order shear deformation theory at first, and utilize the spline finite point method to set up a new dynamic model of piezoelectric intellectual plate. Secondly ,a corresponding MATLAB program is written according to the theory, and has analysed the deformation of the piezoelectric intellectual plate. In the end , this paper has analysed the vibration control of the piezoelectric intellectual plate. Some results are compared with the analytic values, and have proved the rationality of the results of this paper.

本文首先从高阶剪切变形理论出发，利用样条有限点法，建立了压电智能层合板新的动力模型；其次，利用MATLAB语言编写了相应的计算机程序，对压电智能层合板的变形进行了分析；最后分析了压电智能层合板振动控制问题；其中一部分结果与相应的解析解作了详细的比较，证明了本文结果的合理性。

By the twin-rollers flaker designed by the researchers, flaking on high-moisture(28.9%) corn harvested in Heilongjiang Province by hot-air heating was investigated, which was helpful to solve the cost problem of steam-flaking.

该文利用自行研制的对辊式压片机对黑龙江省新收获的玉米(研究中玉米含水率为28.9%)进行了热风加热后压片的试验研究，这有利于解决干玉米添加蒸汽进行压片时成本较高的问题。

Based on fluidic network analysis method, the conception of common mode error of pressure drop fluctuation measurement system was investigated.

主要针对以差压变送器为核心的动态差压检测系统的特点，应用流体网络分析方法，提出了动态差压检测系统中的共模误差问题。

Analysis of the strain field discovers that the principal compressive and the principal tensile strain rates in the epicenter area are -30.840×10-9/a and 13.956×10-9/a respectively before earthquake, and the principal compressive strain axis is in a direction of N105.4°E which is consistent with the average direction at N107.5°E of the principal compressive stress axis from focal mechanism result.

应变场分析发现，震前震中区的主压与主张应变率分别为-30.840×10-9/a与13.956×10-9/a，主压应变轴N105.4°E与震源机制解得到的主压应力轴的方向N103°E一致。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。