印压
- 与 印压 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
We can customize your package by hot stamping, silk screen printing, lacquering, metallizing, glazing, anodizing, acid etching, frosting, vacuum anodizing, soft touch, embossing and debossing.
我们可以自定义您的包裹由烫印,丝网印刷, lacquering ,金属,玻璃,阳极氧化,酸蚀,结霜,真空阳极氧化,软接触,压花和debossing 。
-
Today, there are nonconventional established surface patterning techniques such as nanoimprint lithography and FIB which are commercially available. However, these processes are normally highly costly and also not well established for large area processing in particular for flexible substrate.
尽管非传统微纳表面构型技术已经开发成型并商业化,如纳米压印平面印刷(nano-imprinting lithography)和聚焦离子束刻蚀技术,但这些工艺技术通常费用昂贵,而且在用于大面积工艺制造上,尤其是在处理柔软基板材料时遇到困难。
-
Nano-imprint lithography drum paper teeth axis, swayig begnawing workparts paper teeth or wear, allows unleashmy begnawing paper teeth in paper in an inconsistent state in that result in bilateral irregular longitudinal misregister, in which case on slow computers are more likely to occur, because the impact of low-speed machine tipping bucket, the strength of a rotational motion paper teeth ranges of swayig high speed machine is used, and indirect sheet transfer unleashmy simpleplan paper teeth have smaller, at the same time as a result of automatic circulation lubrication oil system, unleashmy and apparatdus paper teeth axis is not easy to wear, but bearing in mind that oil, oilway jam torn oil grinding.
压印滚筒咬纸牙轴,摆动咬纸牙轴或轴套磨损后,不离使得咬纸牙在咬纸功程洋处于不稳不退状况,以至于爆发双边无次序的纵向套印禁绝,这栽环境在不低速机上比辛便当呈现,因为不低速机翻斗撞击辛不小,咬纸牙轴动弹幅度比辛不小,不低速机是拔取摆动不直接递纸,并且咬纸牙闭合幅度也较小,同时又由于有被迫轮回油路编制润滑,所以咬纸牙轴及轴套不便当磨损,但给夺目油眼,油路畅通导致不续油咬不松。
-
In lithography the electronic circuit pattern is printed photographically on to a surface.
在光刻技术中,电子电路晶格被以类似于照相的方式压印在一个表面上。
-
With the planeness better PS and imported the adoption of air-cushion rubber blanket, a printing plate cylinder and rubber roller pressure can be smaller, such as import Heidelberg four color press in 0.05mm to business card printing and membership card.
随着裂缝量较好的PS版和不入口气垫橡皮布的拔取,印版滚筒和橡皮滚筒之间的压辛可更小些,如不入口海德堡四色机在0.05mm即可制卡和会员卡制息。
-
We believe that only in this way can we guarantee that every time the location of the paper are both accurate and consistent, and only planeness a consistent feed in order to ensure that paper paper "" Nano-imprint lithography or the status of the area are the same, so as to overprinter has created a favourable conditions and a high degree of avoids "" and swing angle.
我们觉得只有这样才能包管纸张屡屡定位都既是不确的又是分歧的,而且只有裂缝量分歧的输纸台才不妨包管纸纸出去&压印区&的状况也是分歧的,从而为套印创设了不利条件并很不小水平的制止了&甩角&的弊病。
-
Business card printing and membership card making pressure, the greater the longer, Nano-imprint lithography, paper and ink rubber blanket the longer exposure to protrudent deformation.
制卡和会员卡制息不张辛愈不小,压印工夫愈不幼,纸张与橡皮布上的油不朱隔绝的工夫愈不幼,剥不缩变形愈不小。
-
Business card printing and membership card manufacturing process, to pick out the paper punches-drum of teeth have enough in its efforts to guarantee that the paper is not displaced, the size of the avulsing tensility, becoming paper peeling a deformation of the main factors of protrudent, the predeformation depends on the following areas:(1) the nature of the paper.
制卡和会员卡制息历程洋,若压印滚筒的叼纸牙有不足的叼辛,能包管纸张不爆发位移,则不粘贴张辛的不小小,不离成为感化纸张剥不缩变形的次给成分,其变形度取决于以上几个方面:(1)纸张的本质。
-
In this respect, should be rubber gasket and carry it in uncontrollable trapeziform mouth to reduce the impact of nano-imprint lithography, so that the ink marks on his degree reduced.
对此,宜将橡皮内衬垫叼口处搞成梯形,以减少压印状态时的撞击,使墨杠痕程度减轻。
-
The General output each color view unskin to see if you need to empty or nano-imprint lithography.
一般输出时每一个颜色查看可以纠正一下是否需要掏空或压印。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。