印压

All dies containing coining stations shall have a minimum .750 hardened plate under each station for support.

在有压印工步的地方，至少有一块。750厚的热处理板支撑。

Hence this technology is the combination of the advantages of room temperature nanoimprint lithography with the capillary force lithography.

因此，薄层软刻蚀技术可以克服普通微模塑方法制备分离图形困难和纳米压印技术中需要使用巨大机械压力的缺点。

For example, screen the ink film not only need to have certain hardness to resist abrasion and scratching, innovativeink bhlf and solvents, and so on at the same time there must be sufficient flexibility for the convenience of people on the cards and membership cards to make products in Bend, die-cutting and pressure concavo-convex.

比如说，网印油墨所形成的墨膜不但要具有一定的硬度，以抵抗磨损、划伤、油墨堆积和溶剂侵蚀等问题，同时还要有足够的灵活性，方便人们对制卡和会员卡制作品进行弯曲、模切和压凹凸。

Using a special process: die-cutting, pressure concavo-convex, anodized foil stamping, UV glazing, oil, etc.

使用特殊工艺：模切、压凹凸、电化铝烫印、UV上光、过油等。

After cleaning skin with face cream, dorp proper essence on cotton bud with burette, then coating on acne cyst with the cotton swab, and gently press 1 to 2 minuts, making effective ingredients permeate into the skin.

洁面后，用滴管往棉签上滴适量的精华液，用棉签涂于痘痘及痘印处，并轻压1-2分钟，使有效成分渗入皮下，轻微者每天1 - 2次，严重者每天3 - 4次。

In the molecular dynamics simulation model, the metallic thin film and the mold, made of gold and nickel, respectively, are formed in face central cubical single crystal.

本文提出三维分子动力学模型模拟奈米压印之制程，并且研究模具线宽及金属薄膜厚度对於结构成形的影响，模拟中所采用的材料为镍模具及金薄膜，排列的晶格结构为单晶面心立方结构。

The impression cylinder of J2108 offset press is regarded as research object in paper,and the deflection of cylinder is researched as simply supported beam with variable cross section .

以J2108型胶印机压印滚筒为研究对象，将滚筒挠曲变形作为变截面简支梁问题来研究，考虑重力载荷影响，通过积分法得到滚筒在印刷压力和重力载荷作用下的挠曲变形方程和曲线，应用MATLAB7.0平台上编写了印刷滚筒挠曲变形计算程序，为滚筒结构的合理设计提供了依据。

This paper studies on the impression cylinder of J2108 offset press. With finite element method, deflection character of cylinder is achieved in static and dynamic load. Active-compensation to improve flexing-change of cylinder is bring forward, and its compensation character is simulated.

本文以J2108型胶印机压印滚筒为研究对象，通过有限元分析获得滚筒动静态挠曲特性，提出用主动补偿方法改善滚筒挠曲变形，并仿真分析了补偿特性。

By using ultraviolet imprint technology, the replication of micro-structure diffraction grating is studied.

研究了利用紫外压印技术复制微结构光栅的方法。

Doctor blade: The flexible steel blade on a photogravure press which removes the surplus ink from the face of the cylinder or plate before the impression is made on the paper.

刮墨刀：照相凹版机上的软钢刀片。它的作用是在压印纸张前，清除版片或版圆筒上多余的油墨。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。