单体

The influences of such factors as composition of comonomers, initiator, cross-linking agent and neutralizer on the absorption capacity of the resins were also discussed.

通过实验对合成高吸水性树脂反应影响因素如单体的类型及量、引发剂的类型及量、交联剂的类型及、中和度、反应温度等作了详细的探讨。

The phase transition temperature increases and the transition ranges tends to be broad when PNIPA brushes were substituted with P or P(NIPA-co-NVP) brushes obtained by the copolymerization of NIPA with AA and NVP, respectively. However, the phase transition is not obvious if adding excessive hydrophilic comonomer.

结果表明，纯PNIPA刷的相变温度在29℃~33℃之间，通过共聚所得的单一P或P(NIPA-co-NVP)刷均使相转变温度提高，转变区域拓宽，当亲水性共单体的量过多时会导致相变过程不明显。

The results showed that the thermo-sensitivity of hairy PNIPA changed obviously in the presence of hairy PAA as polyelectrolyte.4-cyanopentanoic acid dithiobenzoate as soluble reversible addition-fragmentation chain transfer agent was directly added into the above PS particles with photo-initiator on the surface and NVP or NIPA as monomer.

其次，将水溶性RAFT试剂直接引入上述光引发聚合体系，探讨连续相中RAFT试剂的存在对微球表面N-乙烯基吡咯烷酮或N-异丙基丙烯酰胺聚合的影响，考察了RAFT试剂对聚合过程中微球壳层高分子毛发厚度和单体转化率变化趋势。

Firstly, micron-size monodisperse polystyrene particles were prepared by emulsifier-free polymerization. Then the photo-initiator with double bond and ester group were attached on the surface of the PS particles by copolymerization using "starve" addition together with styrene. Finally both poly and poly(N-isopropylacrylamide) as hybrid hairy homopolymers were grafted on the surface of the PS particles by "grafting from" photo-initiation with sequential addition of AA and NIPA.

首先，通过无皂乳液聚合法合成亚微米级单分散聚苯乙烯微球种子，半连续补加法表面负载光引发剂，运用"从表面接枝"技术及顺序添加相关单体的工艺这三步法，成功制得表面含电解质PAA及温敏性PNIPA的混合型毛发，探讨其制备过程和特性研究，表明PAA链的存在对PNIPA链的温敏性有明显影响。

The method for determination of acrylic nitrile and styrene monomer in polymer polyatomic alcohol by gas chromatography was introduced.

介绍采用气相色谱法测定聚合物多元醇中丙烯腈、苯乙烯单体含量的方法。

The conclusions were as follows: theνO-H andνC=O IR absorption maxima shifted towards higher wave numbers after imprinting 17β-estradiol on TFMAA-co-TRIM copolymer with the red shift of theνO-H groups being apparent after precipitation polymerization for 16h while that forνC=O groups being observed after polymerization for 24h. A strong interaction between TFMAA and 17β-estradiol was confirmed by the high selectivity for 17β-estradiol, as indicted by the values of the separation factor of isomers of 17β-estradiol/17α-estradiol (2.28) and the imprinted factor (3.01). Particle diameter of TFMAA-co-TRIM polymer was between 300 nm and 1.5μm, which suited well for solid phase sorbent throughout at low column pressure. The recognition of imprinting TFMAA-co-TRIM polymer for sterol molecules was driven by enthalpy eluted with acetronitile, and low temperature was in favor of the separation of sterol structure analogues on imprinting column. TFMAA-co-TRIM polymer possessed of determinate anti-heat stability, with melting point beginning at 255.84℃, Tp=257.40℃, control TFMAA-co-TRIM polymer and imprinting TFMAA-co-TRIM polymer were respectively decompounded at 267.79℃and 343.11℃, and solid micro-extraction noddle prepared by the special polymerization also showed definite recognition for 17β-estradiol by GC/MS detecting at 270℃. By selection of various washing and elution solvents, elution reagents of close polymerization system were of more advantage in template molecules retention and recognition on molecularly imprinted solid phase extraction column. At a certain extent, progesterone, 17α-estradiol, 17β-estradiol and 4-androstene-3, 17-dione could be intercepted on the MISPE column. Especially, MISPE had high selectivity for progesterone, and imprinting TFMAA-co-TRIM polymer could achieve adsorption balance within 50 min by absorption kinetics test for 17β-estradiol. However, MISPE column showed better selectivity and enrichment property for 17β-estradiol than C18 and CSPE columns according to the data from HPLC and GC/MS analyses. Recovery of 17β-estradiol on MISPE column was up to 85.5% while when prime extracting solution of milk powder was sampled, the recovery of CSPE and C18 columns were 43.7% and 30.7%, respectively.

通过研究阐明：紫外聚合产物TFMAA-co-TRIM中的νO-H振动吸收峰在聚合16h后红移，νC=O振动吸收峰在聚合24h后红移；TFMAA-co-TRIM对雌二醇异构体的印迹因子达到了3.01，α为2.28，优于其它功能单体参与得到的聚合物识别特性；TFMAA-co-TRIM聚合物粒径介于300 nm至1.5μm之间，作为色谱固定相具有良好的通量和低的柱压；在乙腈流动相中，TFMAA-co-TRIM分子印迹固定相的分离过程主要被焓驱动，低温有利于分子印迹固定相分离甾醇结构类似物；TFMAA-co-TRIM分子印迹聚合物在255.84℃时开始熔融，Tp=257.40℃，聚合物CP的降解温度在267.79℃，MIP降解温度在343.11℃，制备的固相微萃取头初步经GC/MS 270℃的耐热性测定；不同的洗提溶剂筛选证明了选择接近聚合溶剂的洗脱体系更有利于MISPE发挥识别效应；分子印迹固相萃取柱对孕酮、17α-雌二醇、17β-雌二醇和雄烯二酮都具有不同程度的保留特性，可作为此类化合物的吸附材料，特别对孕酮强保留的富集特性，可作为孕酮的选择性识别吸附剂，其分子印迹聚合物对17β-雌二醇的吸附动力学测定显示在50 min内基本达到吸附平衡，具有作为传感器核心敏感材料的潜力；对比萃取奶粉中17β-雌二醇性能，MISPE柱比非分子印迹固相萃取柱和C18柱具有更高的保留，回收率依次为85.5%，43.7%和30.7%。

A noncellular biological entity that can reproduce only within a host cell.

病毒 一种能在寄主细胞中自我复制或繁殖的生物单体。

Alternatively, like allopolyploids, they may arise by the nondisjunction of chromatids during the mitotic division of a zygote.

与异源多倍体相似的是，它们也是在有丝分裂中合子的染色单体不分离形成的。

Tetraploid organisms may arise by the fusion of two diploid gametes that have resulted from the nondisjunction of chromosomes at meiosis, or by nondisjunction of the chromoosomes during the mitotic division of a zygote.

四倍体的产生可能是由于两个二倍体配子发生融合，这种二倍体配子又是在减数分裂中染色体不发生分离而形成。四倍体也可能因为受精卵进行有丝分裂时染色单体未发生分离而形成。

New architecture involves in optic protection and nonfigurative protection for urban historical environment. The second arrangement is historical region.

历史地段不同于单体历史建筑，它较为复杂，对它的设计必须采取小规模渐进式的设计方式，而且应较多应用抽象提取的方法。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。